@article { author = {Aryafar, Ahmad and Yousefi, Saeed and Khosravi, Vahid and Khorashadi, Mohammad}, title = {Using stepwise factor analysis (SFA) and geochemical mineralization probability index (GMPI) in order to intensify the geochemical anomalies associated with vein-type copper mineralization in Kardgan 1:100000 sheet, East of Iran}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {1-13}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.95598.1667}, abstract = {Kordagan 1:100,000 sheet is located in the northern Lut structural block and in South Khorasan province. In this area, mineralogy is mainly a vein controlled by fault structures with a northwest-southeast trend. In order to improve the results of the exploration, three solutions were used. To eliminate interfering elements and obtain clean factors in the multivariate statistical technique of stepwise factor analysis (SFA) was used. In addition to eliminate ineffective elements in the calculations, the elements that were not related to vein-type copper mineralization were also excluded. Finally, using the GMPI method, the obtained anomalies were intense. During the exploratorion operations in the Kordgan region, 836 stream sediment and 30 duplicate samples were taken. The samples were analyzed by ICP method by the Geological Survey and Mineral Exploration of Iran. Through the SFA in three step, the elements Ag, Ni and Cd were omitted from factor analysis calculations. In the next step, the elements Co, Cr, Fe, Mn, Sc, Ti, V, Zn, Sr, and W, which did not correspond to vein-type copper mineralization, were removed and factor analysis was prformed again. The results classified the elements into three factors, which were integrated and classified by GMPI method. Based on the results, eight favorable exploration areas were detected. These area was entirely compatible with the former investigation and also faults and favorable geological units for veins reserves such as Andesite and Andesitic tuff with Eocene age. It seems that the applied methods, by using multi-elemental geochemical signatures and integrating them appropriately, can identify and deduce anomalies consistent with other exploratory evidence.}, keywords = {Stepwise factor analysis (SFA),Geochemical mineralization probability index (GMPI),Favorable exploration areas,Kordagan area,vein-type copper mineralization}, title_fa = {شدت بخشی آنومالی های مس رگه ای در ورقه 1:100000 کردگان با آنالیز مرحله ای SFA و GMPI}, abstract_fa = {ورقه 1:100000 کردگان در پهنه ساختاری لوت شمالی و در استان خراسان جنوبی قرار دارد. در این محدوده، کانه‌زایی عمدتاً به صورت رگه‌ای است که توسط ساختارهای گسلی با روند شمال غربی- جنوب شرقی، کنترل می‌شود. به منظور بهبود نتایج عملیات اکتشاف از سه راهکار استفاده شد. برای از بین بردن عناصر مزاحم و رسیدن به فاکتورهای تمیز در روند پیاده‌سازی روش آماری چند متغیره از روش آنالیز فاکتوری مرحله‌ای SFA استفاده شد. علاوه بر حذف عناصر بی اثر در محاسبات، عناصر غیر مرتبط با تیپ کانی‌سازی مس رگه‌ای نیز کنار گذاشته شد. در نهایت با استفاده روش نوین GMPI، آنومالی‌های بدست آمده، شدت بخشی و مرز دقیق آن‌ها مشخص شد. در طی عملیات اکتشافی در منطقه کردگان، 836 نمونه رسوبات آبراهه‌ای و 30 نمونه تکراری برداشت شد. نمونه‌های رسوبات آبراهه‌ای با روش ICP توسط سازمان زمین‌شناسی و اکتشافات معدنی شمال شرق کشور مورد تجزیه شیمیایی قرار گرفت. با انجام روش SFA در سه مرحله، عناصر Ag، Ni و Cd از محاسبات آنالیز فاکتوری کنار رفتند. در مرحله بعد عناصر Co، Cr، Fe، Mn، Sc، Ti،V ، Sr، Ba و W که همخوانی با تیپ مس رگه‌ای ندارد حذف شدند و مجدداً آنالیز فاکتوری انجام شد. نتایج به دست آمده عناصر را در سه فاکتور طبقه بندی کرد که با روش GMPI تلفیق و کلاسه بندی شدند. بر اساس نتایج، 8 منطقه امیدبخش اکتشافی به دست آمد که با تحقیقات گذشته منطقه و همچنین گسل‌ها و واحدهای آندزیت و توف آندزیتی با سن ائوسن به عنوان سنگ مناسب ذخا‌یر رگه‌ای، همخوانی دارد. به نظر می‌رسد روش‌ مورد استفاده قادر است با به کارگیری اثرهای ژئوشیمیایی چندعنصری و تلفیق این اثرها، آنومالی‌ها را منطبق با سایر شواهد اکتشافی شناسایی و استنتاج نمایند.}, keywords_fa = {آنالیز فاکتوری مرحله‌ای SFA,شاخص احتمال کانی‌سازی ژئوشیمیایی GMPI,مناطق امیدبخش اکتشافی,ورقه کردگان,تیپ مس رگه‌ای}, url = {https://ijme.iranjournals.ir/article_40498.html}, eprint = {https://ijme.iranjournals.ir/article_40498_5ccae71cb5359dd1008537e1de35ad16.pdf} } @article { author = {Faraji -Kalarijani, Hamid Reza and Jalali, S.M.E}, title = {Identifying and Prioritizing Factors Affecting the Success of Public /Private Participation in Mining Projects}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {14-29}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.105336.1714}, abstract = {Improvement of the value chain of mining and mineral industries requires a lot of investment. Considering the current condition of the country, this cannot be achieved just by the public budget. One possibly effective approach in financing is the participation of public and private parties is Public-Private Participation (PPP). In order to apply this method to the mining projects, it is necessary to identify factors effective on success through studying and analyzing other countries' experiences and experts' solutions. In this manuscript, in order to identify and prioritize factors effective on PPP success in mining projects, previous researches and papers were studied, success-factors identified and several questionnaires prepared and were given to the experts in order to prioritize them. Then, the results were ranked using Friedman Test. The results of this research showed that through different factors, "defining the appropriate project" has the highest importance on the success of PPPs. Next important ones are payment mechanisms, proper contracts, appropriate political and social environment and legislating new laws, respectively.}, keywords = {mining investment,Public-private partnership,PPP,success-factors}, title_fa = {شناسایی و اولویت‌بندی عوامل مؤثر بر پیاده‌سازی موفق مشارکت عمومی‌– ‌خصوصی در پروژه‌های معدنی}, abstract_fa = {تکمیل زنجیره‌ی ارزش بخش معدن و صنایع معدنی نیازمند سرمایه‌گذاری زیادی است که در شرایط فعلی کشور تامین آن با اتکا به بودجه عمومی امکان‌پذیر نیست. استفاده از روش مشارکت عمومی‌–خصوصی (PPP) یکی از راه‌کارهای موثر در تامین مالی با مشارکت و همکاری بخش خصوصی است. پیاده‌سازی درست PPP در پروژه‌های معدنی مستلزم شناسایی عوامل موثر بر موفقیت از طریق بررسی و مطالعه تجربه‌های کشورهای جهان و هم‌چنین استفاده از نظرات صاحب‌نظران و متخصصان است. در این پژوهش برای شناسایی و اولویت‌بندی عوامل موثر بر موفقیت PPP در پروژه‌های معدنی با مطالعات کتابخانه‌ای و بررسی اسناد و مدارک، عوامل اصلی موفقیت شناسایی شده و برای اولویت‌بندی آن پرسش‌نامه‌هایی تدوین و در اختیار خبرگان قرار گرفت و نتایج پرسش‌نامه با استفاده از آزمون فریدمن رتبه‌بندی شد. نتایج پژوهش نشان می‌دهد که تعریف پروژه مناسب، بیشترین اهمیت را در بین عوامل موثر بر موفقیت پروژه‌های مشارکت عمومی- خصوصی دارد و عوامل تنظیم سازوکار پرداخت، عقد قرارداد مناسب، محیط سیاسی و اجتماعی مناسب و تدوین و تصویب قوانین در رتبه‌های بعدی قرار دارند}, keywords_fa = {تامین سرمایه,مشارکت عمومی‌–‌ خصوصی (PPP),عوامل موفقیت,معدن}, url = {https://ijme.iranjournals.ir/article_40497.html}, eprint = {https://ijme.iranjournals.ir/article_40497_493ec5326b387e2aa44a733c3adf456d.pdf} } @article { author = {Seyedrahimi-Niaraq, Mirmahdi and zare, mehdi and Ghavami-Riabi, Reza}, title = {Investigating the Characteristics of shear zone gold deposit by implementation of discriminant functions on the Probability plot model}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {30-42}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.105190.1712}, abstract = {One of the most important goals in mineral exploration is the identification of mineralization areas. Since gold is considered as the financial support of countries, this is one of the important requirements in identifying and evaluating these deposits. Therefore, samplings and exploratory studies must be designed to minimize the risk of exploration process. The mineralization of gold in Kurdistan region of Iran, in the Sanandaj-Sirjan zone, has been categorized as a shear zone gold type. In order to optimize separation of gold mineralized anomalous areas, it is necessary to carefully investigate the characteristics of the sub-population. In this research, the discriminant analysis method was implemented on the probability plot modeling results for a more accurate investigation and an improvement in results. Accordingly, the stream sediment samples were used for 21 geochemical variables (Zn, W, V, Ti, Sn, Sb, Pb, Ni, Mo, Mn, Hg, Cu, Cr, Co, Bi, Be, Ba, B, Au, As, Ag). Initially, four sub-population were identified among the data of the gold element by modeling the probability diagram and the approximate background and anomaly limits were estimated analyzing the model.. Then among the raw data, the concentrations of 5, 15 and 30 ppb were selected as the boundaries of the papulations, and the values of 15 and 30 ppb were introduced as the anomaly’s thresholds with an area of 38 and 26 km2, respectively. Subsequently, each of these sub-population were coded. The data was classified using the discriminant analysis- DA method, with three discriminant functions, DF, consisting of 6 variables (Ag, Au, Co, Mn, Mo, V) with the greatest effects on the samples classification. The five variables next to the gold element were identified as the most effective elements in identifying gold anomaly samples that were largely consistent with the gold characteristics of shear zones. Original methods and cross-validations were used in order to validate functions in classifying the population. After this validation the areas were categorized with 87% and 83% of correctness. The results of DFM on probability model can be used to optimize the exploratory operations and classify new exploratory data to the background or anomaly using the six geochemical parameters mentioned above and it can be an effective guide to the subsequent stages of exploratory operations.}, keywords = {Modeling,Bioleaching,Neural Networks,fuel oil ash}, title_fa = {بررسی ویژگی های زیرجوامع کانی سازی طلای تیپ کوهزائی با پیاده سازی توابع تفکیک آنالیز تمایز روی مدل نمودار احتمال در چهار گوشه سقز}, abstract_fa = {کانی­ سازی طلا در منطقه کردستان ایران، واقع در زون سنندج – سیرجان، به­ عنوان تیپ طلای پهنه­ های برشی طبقه ­بندی شده است. برای جداسازی بهینۀ نمونه ­های آنومال کانی ­سازی شدۀ طلا نیاز به بررسی دقیق ویژگی ­های زیرجوامع ضروری به ­نظر می­رسد. در این تحقیق برای بررسی دقیق­ تر این ویژگی­ ها و بهبود نتایج، روش آنالیز تمایز روی نتایج مدل­سازی نمودار احتمال پیاده ­سازی شده است. بدین منظور از نمونه­ های رسوبات آبراه ه­ای 21 متغیر ژئوشیمیایی (Zn, W, V, Ti, Sn, Sb, Pb, Ni, Mo, Mn, Hg, Cu, Cr, Co, Bi, Be, Ba, B, Au, Ag) استفاده شده است. ابتدا با انجام مدل­سازی نمودار احتمال­ چهار زیرجامعه در بین داده­ های عنصر طلا شناسایی شد و با تحلیل مدل حدود تقریبی زمینه و آنومالی تخمین زده شد. سپس، از بین داده­ های خام، مقادیر غلظت­های 5، 15 و 30 ppb به ­عنوان مرز جوامع انتخاب شدند و در نهایت مقادیر 15 و 30 ppb به ­عنوان حدآستانۀ آنومالی ­ها به ­ترتیب با مقدار مساحت 38 و 26 کیلومترمربع معرفی شد. سپس به هر یک از این زیرجوامع کد اختصاص داده و با استفاده از تکنیک آنالیز تمایز نسبت به کلاسه ­بندی داده­ها با سه تابع خطی متشکل از 6 متغیر (Ag, Au, Co Mn, Mo, V) که بیشترین اثر را در کلاسه ­بندی نمونه­ ها داشته ­اند، اقدام شد. پنج متغیری که در کنار عنصر طلا قرار گرفته­ اند به ­عنوان مؤثرترین عناصر در شناسایی نمونه ­های آنومال طلا معرفی شدند. به منظور اعتبار سنجی توابع آنالیز تمایز، در کلاسه­ بندی جوامع، از روش­ های اصلی و ارزیابی متقابل استفاده شد. با این اعتبارسنجی، داده ­ها با صحت معادل 87% و 83% طبقه ­بندی شدند. نتایج توابع تفکیک روی مدل نمودار احتمال قادر است تا در بهینه ­سازی عملیات اکتشافی و رده­ بندی داده­ های جدید اکتشافی منطقه به زمینه یا آنومال با استفاده از شش پارامتر ژئوشیمیایی مذکور، راهنمای مؤثری در انجام مراحل بعدی عملیات اکتشافی باشد.}, keywords_fa = {داده‌های ژئوشیمیایی عنصر طلا,رسوبات آبراهه‌ای,مدل‌سازی نمودار احتمال,آنالیز تمایز,جامعه زمینه و آنومالی,مناطق آنومالی}, url = {https://ijme.iranjournals.ir/article_40499.html}, eprint = {https://ijme.iranjournals.ir/article_40499_1748614ec9ed864690a0bcc0ccd8b13b.pdf} } @article { author = {Hazrati Dastjerd, Ali and Vahabi, Shamsoddin and Khodayari, Ali Asghar and Nouri Qarahasanlou, Ali}, title = {Application of availability importance measure for system bottleneck determination (case study: Golgohar-e Sirjan iron mine)}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {43-55}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.108706.1731}, abstract = {Trucks are the main hauling machinery in open pit mines. High capital and operational cost requires accurate management and high efficiency of this equipment, this circumstance depends on the accurate understanding of the system and its behavior in different operating conditions. “Importance measure” approach is one of the useful methods that prioritizes system or implement it from different perspectives such as up and down time aiding the engineers for better decision making about management and resource allocating. Reliability, availability and maintainability (RAM) importance measure are combination of system behavior and importance, that by analyzing up and down time prioritizes and detection bottleneck of system. In this paper, a comprehensive approach based on availability importance measure for increase performance of a truck from Golgohar mine has been suggested. In this truck, transmission and body subsystem are identified as most and least important subsystem from availability point of view respectively. Also, transmission maintainability has major contribution for increasing system availability.}, keywords = {"Availability","Reliability","Maintainability","Importance measure"}, title_fa = {سنجش اهمیت قابلیت دسترسی در تعیین گلوگاه سیستم حمل و نقل در معدن گل‌گهر}, abstract_fa = {دامپتراک‌ها‎ به عنوان اصلی‌ترین ماشین‎آلات باربری در معادن روباز مطرح می‌باشند. هزینه‎ی سرمایه‎ای و جاری بالای این ماشین‎آلات، مدیریت دقیق و بهره‌کشی حداکثری را می‎طلبد که این موضوع نیز در گرو شناخت دقیق از سیستم و درک رفتار آن در شرایط عملیاتی مختلف می‌باشد. رویکرد "سنجش اهمیت" از جمله روش‌های پرکاربرد در این زمینه می‌باشد که با اولویت‌بندی سیستم یا اجرای آن از منظرهای مختلف مانند وضعیت سرپایی، خواب یا آماده‌بکاری مهندسین را در اتخاذ تصمیمات صحیح مدیریتی و تخصیص منابع یاری می‌دهد. سنجش اهمیت قابلیت اطمینان، تعمیرپذیری یا دسترسی به عنوان تلفیقی از این دو با تحلیل زمان‌های سرپایی و خواب قادر به اولویت‌بندی و تعیین گلوگاه عملکردی سیستم می‌باشند. لذا در این مقاله رویکردی جامع بر اساس سنجش اهمیت قابلیت دسترسی برای افزایش عملکرد یک دستگاه دامپتراک‌ معدن گل‌گهر سیرجان پیشنهاد شد. در این دامپتراک، زیرسیستم انتقال‌قدرت و بدنه به عنوان پراهمیت‌ترین و کم‌اهمیت‌ترین زیرسیستم از نظر قابلیت دسترسی شناخته شدند. همچنین افزایش قابلیت دسترسی دامپتراک در گرو افزایش قابلیت تعمیرپذیری زیرسیستم انتقال‌قدرت می‌باشد.}, keywords_fa = {"قابلیت دسترسی","قابلیت اطمینان","قابلیت تعمیرپذیری","سنجش اهمیت"}, url = {https://ijme.iranjournals.ir/article_38845.html}, eprint = {https://ijme.iranjournals.ir/article_38845_60f055d9c26767b5029736c3a63bff9a.pdf} } @article { author = {Saeedi, Reza and Sadeghi, Mohamadhosein}, title = {Investigation of Insert-Hole Interference Fit Tolerance Influence on DTH Drilling Bit Performance}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {56-67}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.108942.1732}, abstract = {DTH drilling is a reliable method for drilling in medium to hard geological structures. Considering the country's need for different types of drilling bits in various industries, with development of knowledge and production of them, it can limit the vast importation of these products. In this study, process of bit/rock collision taking into account interaction between the insert/body and stresses resulting from interference fit is simulated to determine proper tolerance for fitting, which is the most important factor limiting the life of drilling bit. Simulations were carried out taking account rotary motion of bit in addition to impact in single-insert condition with different angles of collision and also in a 3.5 inch bit with 13 inserts. Mechanical properties of specimens made of DIN1.6580 steel, used for manufacturing of bit body, were obtained through experiments. Then, in order to validate and also obtain appropriate mesh size, results of pin-hub interference fit simulations with selected parameters were compared to Lame's analytical method. Results show that interference tolerance and speed and angle of impact have great influence on stresses and process forces. In case of 1.2% of interference, stresses in bit body are about to reach material strength. In the case of 0.9% and 0.6%, certain amount of plastic strain is also created in the body. The results of this study is greatly helpful in choosing fitting tolerance of inserts into bit body during manufacturing process.}, keywords = {DTH drilling,Interference tolerance,Residual Stress,Thick walled cylinder,Improved Drucker-Prager model}, title_fa = {مطالعه تاثیر میزان تداخل اتصال اینسرت در عملکرد سرمته حفاری درون‌چاهی}, abstract_fa = {روش حفاری ضربه‌ای درون‌چاهی برای حفاری در شرایط متوسط تا سخت زمین شناسی روش قابل اعتمادی است. با توجه به نیاز کشور به انواع سرمته در صنایع مختلف، با گسترش دانش و تولید آنها می‌توان واردات گسترده‌ی این محصولات را محدود کرد. در این پژوهش برخورد سرمته-سنگ با درنظر گرفتن برهم‌کنش دکمه تنگستن کارباید(botton)-بدنه و تنش‌های پسماند حاصل از انطباق تداخلی آنها جهت تعیین تلرانس مناسب برای اتصال دکمه (insert) در بدنه سرمته مطالعه شد. این تلرانس که مهمترین عامل تاثیرگذار در جدا شدن دکمه‌ها و درنتیجه عمر سرمته است در حالت تک‌دکمه (single-insert) با زوایه‌های برخورد مختلف و همچنین برای نمونه کامل سرمته 3.5 اینچ با تعداد 13 دکمه بصورت ضربه‌ای-چرخشی شبیه‌سازی گردید. بدین منظور ابتدا خواص مکانیکی نمونه‌های استاندارد از جنس فولاد DIN1.6580 که برای ساخت بدنه سرمته استفاده می‌شود از طریق آزمایش‌های تجربی بدست آمد. سپس به منظور صحت‌سنجی و نیز بدست آوردن اندازه شبکه (Mesh size) مناسب، نتایج شبیه‌سازی اتصال تداخلی با روش تحلیلی مقایسه گردید. نتایج نشان داد که میزان تداخل و سرعت و زاویه برخورد تاثیر زیادی در تنش‌ها و نیروهای فرآیند دارند. در تداخل 1.2%تنش در بدنه سرمته تقریباً به استحکام نهایی آن می-رسد. در حالت 0.9% و0.6% مقداری کرنش پلاستیک نیز در بدنه ایجاد خواهد شد. حفاری در شرایط کاری واقعی با سرمته‌ی ساخته شده براساس نتایج بدست آمده کاملاً موفقیت‌آمیز بود. نتایج این مطالعه در انتخاب میزان تداخل دکمه-سرمته در فرآیند ساخت آن کمک شایانی می‌نماید.}, keywords_fa = {سرمته حفاری DTH,انطباق تداخلی,تنش پسماند,استوانه جدار ضخیم,مدل دراکر-پراگر توسعه یافته}, url = {https://ijme.iranjournals.ir/article_40500.html}, eprint = {https://ijme.iranjournals.ir/article_40500_235243973343595fbdaee4c5feb5044a.pdf} } @article { author = {Rastegar, Seyed Omid and Beigzadeh, Reza}, title = {Using Artificial Neural Network to modeling of valuable metals bioleaching from fuel oil fly ash using Acidithiobacillus ferrooxidans}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {68-75}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.114427.1752}, abstract = {In this study, the modeling of vanadium, nickel and copper bioleaching from fuel oil ash ash using artificial neural networks was investigated. In the obtained models, the extraction percentage of metals was investigated as a function of factors such as initial pH (from 1-2.5), initial Fe2+ concentration (from 0 – 9 g/l), initial bacterial inoculation (from 1 – 10%) and process time (from 0-15 day). Three neural network models were presented to estimate the extraction percentage of metals. The propagation error method and Levenberg–Marquardt algorithm were used for training. Furthermore, trial and error method was used to determine the optimal number of neurons. One quarter of the data were used to evaluate the model and were not used for training process. The Mean Relative Errors (MRE) were obtained 5.35%, 3.07% and 2.82% for V, Ni and Cu, respectively. Also the higher 0.99 of R2 indicates the validity of the obtained models.}, keywords = {Modeling,Bioleaching,Artificial neural networks,fuel oil ash}, title_fa = {استفاده از شبکه عصبی مصنوعی به منظور مدلسازی فرایند بیولیچینگ فلزات با ارزش از خاکستر سوخت نفت کوره با استفاده از باکتری اسیدی تیوباسیلوس فرواکسیدانس}, abstract_fa = {در این مطالعه مدلسازی بیولیچینگ فلزات باارزش وانادیوم، نیکل و مس موجود در خاکسترهای سوخت نفت‌کوره با استفاده شبکه‌های عصبی مصنوعی بررسی می‌شود. در مدل‌های به‌دست‌آمده، درصد استخراج فلزات به‌عنوان تابعی از فاکتورهای pH (در بازه 1- 5/2)، غلظت اولیه یون Fe2+ (در بازه 0- 9 گرم بر لیتر)، درصد تلقیح باکتری (در بازه 1- 10 %) و زمان (در بازه 0- 15 روز) فرایند مورد بررسی قرارگرفته است. سه مدل شبکه عصبی برای تخمین درصد استخراج هریک از فلزات ارائه شد. از روش پس انتشار خطا و الگوریتم لونبرگ-مارکورت برای آموزش شبکه استفاده شد. یک‌چهارم داده‌ها در فرایند آموزش شبکه عصبی استفاده نشد و برای ارزیابی مدل مورد استفاده قرار گرفت. متوسط خطای نسبی (MRE) برای وانادیوم، نیکل و مس به ترتیب برابر با % 35/5، % 07/3 و % 82/2 به دست آمد. همچنین مقدار بزرگ‌تر از 99/0 از کسر مطلق واریانس (R2) بیانگر تائید اعتبار مدل‌های به دست آمده از شبکه عصبی می‌باشد.}, keywords_fa = {مدلسازی,بیولیچینگ,شبکه‌های عصبی,خاکستر نفت‌کوره}, url = {https://ijme.iranjournals.ir/article_40501.html}, eprint = {https://ijme.iranjournals.ir/article_40501_fd4cdac991c1fb3207bf005328444b8d.pdf} } @article { author = {Khaledi, Hamed and Mohammadnejad, Sima and Abdollahy, M}, title = {Ore Characterization and processing of high nugget effect Azghad gold ore}, journal = {Journal of Mining Engineering}, volume = {15}, number = {47}, pages = {76-86}, year = {2020}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {10.22034/ijme.2020.115071.1755}, abstract = {Nugget effect is a common feature of many vein-style gold deposits. This style of mineralization results in complication in many exploitation stages including resource and average grade estimation, representative sample selection, ore characterization as well as processing. Accurate and reliable ore characterization is a vital stage in any mineral processing project. Ore characterization in high nugget effect gold ores is so complex due to uncertainties associated with representativity of the selected sample. The main challenge is to provide a representative sample for identification of each process mineralogy parameter such as average grade, liberation, grinding size, mineral association, floatability, etc. Here, different protocols are collected and compared to draw a comprehensive picture of the available methods. The results are examined on a high nugget effect gold ore from Northeast of Iran, Azghad mine. Processing experiments were conducted to develop a process suitable for Azghad gold mine. To investigate the feasibility of pre-concentration, gravity methods using a Nelson separator was applied on the oxide sample as the main gold vein. 43.3% of total gold was concentrated in the gravity concentrate with only 2% weight recovery, suggesting gravity concentration can be considered as an efficient method in this ore. Gold preg-robbing experiments were performed for Shale sample due to the organic matter, clay minerals and mica. Preg-robbing potential of the shale ore was determined to be 1.1 ppm. Optimization of operating parameters was performed by central composite design method for the combined oxide and shale samples.}, keywords = {High nugget effect,Ore Characterization,Gold Ores,Azghad Mine,Cyanidation}, title_fa = {مشخصه یابی و فرآوری کانسنگ طلای ازغد با اثرناگت بالا}, abstract_fa = {یکی از چالش های پیش رو در شناسایی و مشخصه یابی غالب کانسنگ های طلای رگه ای، وجود اثر ناگت بالا می باشد. بهره برداری از این ذخایر چه در مرحله برآورد ذخیره و چه در مرحله فراوری با پیچیدگی های فراوانی رو به رو است. در این پژوهش کانسنگ طلای ازغد با اثر ناگت بالا با به کارگیری روشهای نوین عیارسنجی مورد بررسی قرار گرفته است. معدن ازغد دارای سه رگه ی اکسیدی، شیلی و سیلیکاتی می باشد. داده های عیارسنجی اولیه به روش قالکاری وجود اثر ناگت بالا را تایید کردند. با مقایسه روش های مختلف عیارسنجی، روش لیچینگ کامل با شرایط 5 کیلوگرم نمونه به ابعاد زیر 75 میکرون و میزان سیانور سدیم 5/1 گرم بر لیتر در pH برابر 5/10 به عنوان روش مناسب جهت عیارسنجی این نمونه تعیین شد. بر این اساس عیار طلا در رگه های اکسیدی، سیلیکاتی و شیلی، برابر 7/4، 4/0 و 25/0 پی پی ام تعیین گردید. همچنین مطالعات فازشناسی طلا به روش لیچینگ تشخیصی نشان داد 7/75 درصد طلا آزاد، 0/18 درصد درگیر در فازهای سولفیدی و 3/6 درصد طلا در فازهای سیلیکاتی توزیع یافته است. آزمایش های فراوری به منظور توسعه فرایند مناسب در این کانسنگ صورت پذیرفت. بهینه سازی پارامترهای عملیاتی موثر، میزان خردایش 75=d80 میکرون، مصرف سیانور سدیم ۴۱/۱ گرم بر لیتر و 30 درصد جامد در 5/10=pH و مدت زمان 24 ساعت را تایید کرد. میزان بازیابی در این شرایط برابر ۹/۸۲ درصد طلا به دست آمد. نتایج حاصل از این تحقیق می تواند به نحو موثری در شناسایی، مشخصه یابی و فراوری کانسنگ های طلای با اثر ناگت بالا استفاده شود.}, keywords_fa = {اثر ناگت,طلا,سیانوراسیون,مشخصه‌یابی,ازغد}, url = {https://ijme.iranjournals.ir/article_38843.html}, eprint = {https://ijme.iranjournals.ir/article_38843_a887f37f3bc696d9a5ce54f72a1e939f.pdf} }