@article { author = {Dehghani, A and Mansouri, H}, title = {Replacement of Dynamite with ANFO in Tunneling}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {1-14}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {In resent years, dDrilling and blasting is the most applicable methods of excavation of underground structures. In tunnel blasting, the pattern design and the selection of type of explosive used, play a crucial role in achieving the desired results. In Iran, the common explosive used in tunnel blasting is dynamite, which is very expensive compare to ANFO.   In this research, an investigation was carried out to substitute dynamite as a relatively expensive explosive but with high specific energy with ANFO as a relatively cheap explosive with low specific energy. Tests were carried out in Abasaleh Almahdi tunnel, a road tunnel, connecting Eghlid city to Yasooj city, Iran.   At the first stage of the research, the existing pattern was modified (two tests) to improve the results obtained. HCF (Half-Cast Factor), Over Break (OB), Advance Rate (AR) and Specific Cost Factor (SCF) were used to do the quantitative assessment. In the second stage of the research, based upon the modification carried out, substitution of dynamite with ANFO was studied by 10 designed blast tests designed and the best dynamite-ANFO substitution option was suggested.   The results obtained showed that by substituting dynamite with ANFO, as well as an AR of 95%, an OB of less than 5%, a HCF of more than 20% and a reduction in explosive costs up to 32% can be achieved.  }, keywords = {Tunnel,Drilling and Blasting,Substituting dynamite with ANFO}, title_fa = {بررسی امکان جایگزینی دینامیت با آنفو در حفاری تونل‌ها}, abstract_fa = {چالزنی و انفجار  بنا به دلایل مختلف پرکاربردترین روش حفر تونل در سطح جهان است، بنابراین طراحی بهینه الگوی انفجار و انتخاب نوع ماده منفجره تا حد زیادی در اقتصادی بودن  و ایمن بودن حفر تونل مؤثر هستند. در این مقاله، ضمن اصلاح الگوی انفجار تونل راه حضرت اباصالح المهدی (عج) شهرستان اقلید، امکان جایگزینی دینامیت به‌عنوان یک ماده منفجره گران  و  با انرژی ویژه بالا  با آنفو به‌عنوان یک ماده منفجره ارزان و با انرژی ویژه پایین مورد بررسی قرار گرفته است. اصلاح الگوی انفجار فعلی، طی دو انفجار آزمایشی انجام شد. سپس به منظور جایگزینی دینامیت با آنفو 10 مرحله انفجار آزمایشی طراحی و اجرا شد. در هر انفجار آزمایشی، بخشی از دینامیت با آنفو جایگزین شده و پس از انجام انفجار، با در نظر گرفتن میزان پیشروی و هزینه ماده منفجره به کار رفته در انفجار، هزینه ویژه انفجار محاسبه شد. با معیار قرار دادن هزینه ویژه، نرخ پیشروی، بیش حفاری و داغ چال، نحوه خرج‌گذاری بهینه انتخاب شد. هزینه ویژه در الگوی انفجار پیشنهادی که در آن قسمتی از دینامیت با آنفو جایگزین شده است، 32% کمتر از حالتی است که در آن به‌طور کامل از دینامیت استفاده شده است. همچنین نرخ پیشروی بالای ۹۵%، بیش حفاری کمتر از ۵% و داغ چال بیش از ۲۰% در الگوی پیشنهادی حاصل شد.}, keywords_fa = {تونل,چالزنی و انفجار,جایگزینی دینامیت با آنفو}, url = {https://ijme.iranjournals.ir/article_2839.html}, eprint = {https://ijme.iranjournals.ir/article_2839_d45025cc98cdcda35b83defd323ab45b.pdf} } @article { author = {Afraei, S and Madani, H}, title = {The study of effective factors on Hardy Cross method convergence in mine ventilation networks analysis}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {15-21}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Analysis of ventilation networks is one of the most important steps in mine ventilation. Hardy Cross method is one of the oldest and the most common methods of ventilation network analysis. This method is an iterative solution procedure and the equations are repeated until the error becomes negligible. The convergence rate of this method in the first stage depends on the preliminary theoretical values ​​of the branch air quantities and the correct choice of meshes. In addition, there are other factors which may affect the convergence rate. This paper focuses on the investigation and proof of those factors. First, if the summation of the branch air quantity and its relevant mesh errors are negative, the current directory must not be changed. Secondly, mentioned branch air quantity is considered with its algebraic sign in the denominator of the Hardy Cross equation in the next iteration. Then a hypothetical network is analyzed and the Newton- Raphson method was used to validate the results. Results from proven approach are in accordance with Newton- Raphson method results. [i1]   [i1]این جمله نیاز به اصلاح دارد، لکن معدل فارسی آن نیز واضح نیست: " نتایج حاصل از رویکرد اثبات­شده" به چه چیری دلالت دارد؟}, keywords = {Network Analysis,Hardy Cross method,Convergence}, title_fa = {بررسی عوامل مؤثر بر همگرایی روش هاردی کراس در تحلیل شبکه¬های تهویه معادن}, abstract_fa = {تجزیه و تحلیل شبکه‌های تهویه یکی از مهم‌ترین مراحل تهویه معادن به شمار می‌رود. روش هاردی کراس یکی از قدیمی‌ترین و از جمله متداول‌ترین روش‌های تحلیل شبکه‌های تهویه است. این روش یک روش حل تکراری است و طی آن تکرار معادلات آن قدر ادامه می‌یابد تا خطا به حد ناچیز برسد. آهنگ تقارب این روش در وهله اول به مقادیر فرضی اولیه شدت جریان شاخه‌ها و انتخاب صحیح حلقه‌ها بستگی دارد. به علاوه عوامل دیگری نیز بر همگرایی و سرعت آن تأثیرگذار هستند که این مقاله به بررسی و اثبات آن‌ها می‌پردازد. نخست آنکه در صورتی که شدت جریان شاخه‌ای پس از جمع جبری با خطای حلقه‌های مربوط به آن منفی شود، جهت جریان در شاخه یادشده تغییر نکند و دیگر آن‌که شدت جریان شاخه یادشده در محاسبه خطای حلقه‌ها در تکرار بعد، با علامت جبری خود در مخرج رابطه هاردی کراس در نظر گرفته شود. در ادامه یک شبکه فرضی مورد تحلیل قرار گرفته و برای اعتبارسنجی نتایج از روش نیوتن- رفسون استفاده شد. نتایج حاصل از رویکرد اثبات‌شده بر پاسخ حاصل از روش نیوتن- رفسون انطباق دارد.}, keywords_fa = {تحلیل شبکه,روش هاردی کراس,تقارب پاسخ}, url = {https://ijme.iranjournals.ir/article_2840.html}, eprint = {https://ijme.iranjournals.ir/article_2840_5d14ba4ab0fe4f672ed62e1403907414.pdf} } @article { author = {Tabasi, S and Ghavami, R and Doulati, F}, title = {Determination of Residual Component of Gravitimetry Data Using Probability Plot Modeling Method}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {23-32}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = { In this study, modeling of probability diagram method was used to calculate the residual component of gravity data at southwest of Zagros, Iran. The regional and residual components were separated based on the data analysis and evaluation of the various trends modeled on probability diagram. The first, second and optimum approximation of residual components were achieved based on different threshold values resulted from the modeled probability diagram. The regional and residual effects of the first and second approximations were not completely separated from each other in some parts of the study area. The 3D view of residual anomaly map of third trend surface, geological map together with the field investigations show that the optimum approximation map could remove the regional effects due to the deep geological structures from bBouguer anomaly values. Although not considered by the conventional anomaly separation methods, the proposed method takes into consideration the variation of the interested variable in the data set.   }, keywords = {Gravity,Residual component,Regional component,anomaly separation,modeling of probability diagram}, title_fa = {تعیین مؤلفه باقی¬مانده داده¬های گرانی¬سنجی با استفاده از روش مدل سازی نمودار احتمال}, abstract_fa = {در این مقاله روش مدل‌سازی نمودار احتمال در برآورد مؤلفه باقی‌مانده  داده‌های گرانی‌سنجی منطقه‌ای در جنوب غرب زاگرس، به کار رفته است. بر اساس تحلیل داده‌ها و تغییرپذیری روند مدل برازش شده بر نمودار احتمال، مؤلفه‌های ناحیه‌ای و باقی‌مانده از یکدیگر تفکیک شده‌اند. تقریب مرتبه اول، دوم و بهینه از مؤلفه باقی‌مانده داده‌ها بر اساس مرزهای متفاوت حاصل از مدل‌سازی نمودار احتمال ترسیم شده است. در نقشه‌های تقریب مرتبه اول و دوم مؤلفه‌های ناحیه‌ای و باقی‌مانده در بخش‌هایی با یکدیگر همپوشانی دارند. بررسی‌ مدل سه بعدی آنومالی باقی‌مانده روند سطحی مرتبه 3، زمین‌شناسی منطقه و برداشت های صحرایی نشان می‌دهد که نقشه تقریب بهینه، تا حد قابل قبولی اثرات باقی‌مانده را از اثرات ناحیه‌ای مربوط به بی‌هنجاری‌های عمیق جدا کرده است. روش پیشنهادی در این مقاله نسبت به روش‌های متداول تفکیک آنومالی‌ها، با محدودیت‌های کمتر و شناخت بیشتری از تغییرپذیری رفتار داده ها، به تفکیک آنومالی‌ها می‌پردازد.}, keywords_fa = {گرانی¬سنجی,مؤلفه باقی¬مانده,مؤلفه ناحیه¬ای,تفکیک آنومالی,مدل¬سازی نمودار احتمال}, url = {https://ijme.iranjournals.ir/article_2841.html}, eprint = {https://ijme.iranjournals.ir/article_2841_8a91ca55a743383eafeba65bdad88cad.pdf} } @article { author = {Esmaeili, K and Moore, F}, title = {Investigation of Heavy metals Enrichment in Stream Sediments of Sungun Porphyry Copper Deposit}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {33-39}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {The Sungun Porphyry Copper Deposit is located in East-Azerbaijan province, 75km northwest of Ahar city. Due to mining activities, streams of this region (Sungunchay, Pakhirchay, Ilginechay and Zarnekabchay) are exposed to heavy metals contamination such as Cu, Mo, Pb, Zn and Ni. In this relation, to determine contamination degree caused by toxic metals, 27 sediment samples were analyzed and it was found that concentration of Cu, Mo, Pb, Zn and Ni are above permissible limits (local background of these metals). Elements Correlation coefficient indicates that Cu, Mo and Ni are correlated to Fe, while Pb and Zn are correlated to Mn. In addition, results from Enrichment Factor, Geo-accumulation Index, Contamination Factor and Pollution Load Index for sediment samples indicate that potentially toxic metals contamination exists.  }, keywords = {Sungun Porphyry Copper Deposit,heavy metals,Enrichment factor,Contamination Factor}, title_fa = {بررسی غنی شدگی فلزات سنگین ناشی از کانسار مس سونگون در رسوبات آبراهه¬ای}, abstract_fa = {کانسار مس پورفیری سونگون در استان آذربایجان شرقی و در 75 کیلومتری شمال غرب شهرستان اهر واقع شده است. به علت فعالیت‌های معدنکاری، رودخانه‌های این منطقه (سونگون چای، پخیرچای، ایلگینه چای و زرنکاب چای) در معرض آلودگی به فلزات بالقوه سمی از جمله Cu، Mo، Pb، Zn و Ni قرار دارند. به همین دلیل برای تعیین میزان آلودگی رسوبات این رودخانه‌ها به فلزات سنگین، 27 نمونه رسوب از رودخانه‌های محدوده کانسار مس سونگون مورد ارزیابی زمین شیمیایی قرار گرفت و مشخص شد که غلظت عناصر Cu،Mo ، Pb،  Znو  Niدر رسوبات بیش از حد مجاز (غلظت زمینه محلی این عناصر در رسوبات رودخانه‌های منطقه سونگون) است. محاسبه ضریب همبستگی عناصر نشان داد که عناصرCu،  Moو Ni با آهن و عناصر  Pbو Zn با منگنز همبستگی مثبت دارند. همچنین نتایج بدست آمده از محاسبه ضریب غنی شدگی (EF)، ضریب زمین انباشت (Igeo)، ضریب آلودگی (CF) و ضریب بار آلودگی (PLI) برای نمونه‌های رسوب، تأیید‌کننده غلظت‌های بالای این فلزات است.}, keywords_fa = {کانسار مس پورفیری سونگون,فلزات سنگین,ضریب غنی¬شدگی,ضریب آلودگی}, url = {https://ijme.iranjournals.ir/article_2842.html}, eprint = {https://ijme.iranjournals.ir/article_2842_510b8f953089860334095c29f06c7601.pdf} } @article { author = {Kianinia, Y and Khalesi, M.R and Khodadadi, A and Foroutan, R}, title = {Designing Dynamic Simulator of Grinding Circuit using SIMULINK}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {41-49}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Control and online optimization of a process could only be performed if the dynamic model of the system is available. In the case of grinding circuits, dynamic simulation provides substantial information on complex and sometimes non-linear interactions between the components of the system. In this paper, dynamic model of ball mill and cyclone are incorporated in MATLAB/SIMULINK platform and then the system is simulated in open and closed circuits. Such simulation showed that the selected platform is suitable for investigation of responses of the system to the changes in input variables such as flowrate or mean residence time. It was also observed that the transient state between two steady states could be well investigated by the ease of this platform.   }, keywords = {Grinding,Modeling,Dynamic simulation,Simulink}, title_fa = {ساخت شبیه ساز دینامیکی مدار خردایش در محیط SIMULINK}, abstract_fa = {کنترل و بهینه‌سازی روی خط یک سیستم در صورتی امکان‌پذیر است که مدل دینامیکی سیستم در اختیار باشد. با استفاده از شبیه‌سازی دینامیکی می‌توان رفتار غیر خطی و تعامل دینامیکی مدارهای خردایش را بررسی کرد. در این مقاله مدل دینامیکی آسیا بر اساس مدل کلی موازنه جمعیتی و مدل هیدروسیکلون بر اساس مدل پلیت در محیط MATLAB/SIMULINK پیاده‌سازی و مورد اعتبارسنجی قرار گرفت. سپس مدار خردایش آسیا در دو حالت مدار باز و بسته شبیه‌سازی دینامیکی شد و گذار از یک حالت پایا به حالت پایای دیگر مورد بررسی قرار گرفت. نتایج نشان داد که واسط کاربری گرافیکی SIMULINK امکانات بی‌شماری در جهت شبیه‌سازی دینامیکی واحدهای فرآوری مواد معدنی و امکان شبیه‌سازی به قصد کنترل فرآیند را فراهم می‌کند.  }, keywords_fa = {خردایش,مدل‌سازی,شبیه‌سازی دینامیکی,Simulink}, url = {https://ijme.iranjournals.ir/article_2843.html}, eprint = {https://ijme.iranjournals.ir/article_2843_f20a9b2e3c73a4438791bbba0a009c77.pdf} } @article { author = {Naderi, H and Abdollahy, M and Mostofi, N and Koleini, S.M.J and Shojasadati, S.A and Manafi, Z}, title = {kinetics of Chemical leaching of Darehzar low grade copper ore}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {51-60}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {As a part of a research on optimization of  heap bioleaching of Dareh Zar copper mine, Iran,   chemical leaching of low grade ore obtaining from secondary enrichment zone of Dare Zar copper mine was investigated. Copper grade was 0.37 %  and the main mineral of copper is chalcopyrite which is altered to digenite and chalcocite. Effects of temperature, initial Fe concentration, Eh, pH and stirring speed were studied. Results showed that reaction take places at 2 different stages. The kinetic of first stage is fast and an activation energy of 16.5 kJ/mol was acquired. The kinetic of second stage is slow and its activation energy is about 150 kJ/mol. There is no need to add initial Fe because Fe released from pyrite is enough for leaching of digenite and chalcopyrite}, keywords = {chalcocite,digenite,Chemical leaching,Kinetics}, title_fa = {سینتیک انحلال شیمیایی کانه کم عیار سوپرژن مس معدن دره زار}, abstract_fa = {در این تحقیق لیچینگ شیمیایی کانه سوپرژن کم عیار معدن دره زار بررسی شد. کانی های اصلی مس در نمونه، کالکوسیت، کوولیت و کالکوپیریت به همراه کانی‌های کوارتز، میکا، کانی‌های رسی، فلدسپار و پیریت است. تأثیر پارامترهایی مانند دما، غلظت آهن، غلظت یون‌های فریک و فرو و نسبت آن‌ها، pH، درصد جامد  و دور همزن تحت شرایط ثابت (با کنترل عوامل فوق در مقادیر مورد نظر) بررسی شد. نتایج نشان داد که پیریت نقش مؤثری در انحلال مس دارد. میزان تغییر سرعت انحلال پیریت در اثر تغییر عواملی مانند دما، غلظت یون فریک، غلظت یون فرو، پتانسیل و غیره مستقیم بر انحلال کانی‌های مس اثر می‌گذارد زیرا با افزایش انحلال پیریت و مصرف یون فریک توسط آن، سرعت نسبی انحلال کانی‌های مس کاهش می‌یابد. واکنش انحلال شامل دو مرحله با سینتیک متفاوت است. مرحله اول دارای سینتیک سریع با انرژی اکتیواسیون kJ/mol 17 و مرحله دوم دارای سینتیک کند با انرژی اکتیواسیون kJ/mol 140 است.}, keywords_fa = {لیچینگ شیمیایی,کالکوسیت,کانه کم¬عیار,سینتیک}, url = {https://ijme.iranjournals.ir/article_3870.html}, eprint = {https://ijme.iranjournals.ir/article_3870_241f313295b8c2c335481e3a2e7d387d.pdf} } @article { author = {Nikkhah, M and Ahmadi, M and Ghazvinian, A}, title = {A New Method for Determination of Kaiser Effect from Rock Acoustic Emission Signals}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {61-72}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Nowadays, acoustic emission tests based on the Kaiser Effect are increasingly used for estimating in-situ stress in laboratories. The present article proposes an automatic method based on pattern recognition methods, which accurately determines Kaiser Effect by combining the results of different common methods. The proposed method uses the signals obtained from uniaxial pressure tests on samples of pre-loaded sandstone samples sandstone. In the proposed new method, previous maximum stress in samples can be determined directly without analysis of waveform signals. Our results show that pattern recognition methods can be used for determining the point of Kaiser Effect. The developed method has a desirable level of precision for determining the Kaiser Effect point.      }, keywords = {Acoustic emission,Kaiser Effect,Pattern recognition,sandstone,in-situ stress}, title_fa = {ارائه روشی جدید برای تعیین نقطه اثر کایزر در سنگ‌ها}, abstract_fa = {به‌کارگیری آزمایش انتشار اکوستیک و اثر کایزر  (Kaiser Effect)برای تخمین تنش برجا توده سنگ به میزان زیادی افزایش یافته است. در این مقاله یک روش خودکار، مبتنی بر روش‌های شناسایی الگو(Pattern Recognition) ، برای تعیین دقیق اثر کایزر با ترکیب نتایج روش‌های مختلف متداول و تصمیم‌گیری برای تعیین مقدار دقیق‌تر تنش اثر کایزر ارائه شده است. در این روش از داده‌های سیگنال‌های  به‌دست آمده از آزمایش‌های انجام شده بر روی نمونه‌های ماسه سنگ پیش بارگذاری شده استفاده شده است. با این روش جدید پیشنهادی، تنش حداکثر قبلی در سنگ‌ها را می‌توان بطور مستقیم و بدون تحلیل بر روی سیگنال‌های جبهه موج تعیین کرد. نتایج تحقیق نشان می‌دهند که روش‌های شناسایی الگو می‌توانند برای تصمیم‌گیری و تعیین نقطه اثر کایزر استفاده شوند و روش توسعه یافته دقت قابل قبول و مطلوبی برای تشخیص و تعیین نقطه اثر دارد.}, keywords_fa = {انتشار اکوستیک (آوایی),اثر کایزر,شناسایی الگو,ماسه سنگ,تنش برجا}, url = {https://ijme.iranjournals.ir/article_2931.html}, eprint = {https://ijme.iranjournals.ir/article_2931_f2ef62a6714b0726bf446d1bf6c2b02a.pdf} } @article { author = {}, title = {Experimental study on the effect of large scale cavities on mechanical behavior of rock mass}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {73-82}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Due to the presence of large civil projects in the Zagros region, the engineering parameters of Asemari formation rock mass have attracted wide attention. One of the characteristics of this formation is the existence of cavities which based on their that related to the shape and position which can reduce strength and deformation parameters of rock mass. In first part of this research, laboratory modeling is used for evaluation of macro porosity effect on deformation modulus and strength of rock. Porous samples were created by plaster and spherical polystyrene granules with have 4 and 6 mm diameter. The range of porosity investigated was approximately 0-45% for uniaxial stengthstrength and 0-30% for elastic modulus. According to the results, uniaxial compression strength and deformation modulus decrease exponentially and by increasing the size of pores from 4 mm to 6 mm. This , decrease ing in the amount of uniaxial strength and elastic modulus is lower less than 7 percent. In the second part, with regard to thatsince the porous material can be considered as a special case of composite materials, effect of the amount of spherical pores on the elastic modulus was studied by micromechanics method and different homogenizing models. By curve fitting in range of 0-30% porosity, reduction of elastic modulus can be determined by exponential relation. The experimental results match well with models which considered the shape. In porosity of less than 15%, with regard to small differences in Eshelby, Self consistent, Mori-Tanaka and Lielens models, experimental results have good accordance with them. With increased porosity, experimental results tend to Selfself consistent and Eshelby model.          }, keywords = {Large pores,Uniaxial compression strength,elastic modulus,Laboratory modeling,Micromechanics method}, title_fa = {بررسی آزمایشگاهی تأثیر حفرات بزرگ مقیاس بر رفتار مکانیکی توده سنگ و ارزیابی نتایج با استفاده از روش میکرومکانیک}, abstract_fa = {با توجه به وجود پروژه‌های بزرگ زیربنایی در منطقه زاگرس به‌خصوص سدها و نیروگاه‌های برقابی، تعیین پارامترهای مهندسی توده سنگ‌های سازند آسماری، توجهات گسترده‌ای را به خود جلب کرده است. از جمله ویژگی‌های این سازند، وجود  حفرات می‌باشند که بسته به شکل و موقعیت آن‌ها باعث کاهش مقادیر پارامترهای مقاومتی و تغییرشکلی در سنگ می‌‌شوند. در بخش اول این تحقیق برای مطالعه میزان حفرات بر مدول تغییر شکل پذیری و نیز مقاومت تک‌محوری سنگ، از مدل‌سازی آزمایشگاهی استفاده شده است. نمونه‌های متخلخل، از گچ و دانه‌های فوم کروی شکل با قطرهای 4 و 6 میلیمتر ساخته شد. محدوده تخلخل نمونه‌های ساخته شده برای مقاومت تک‌محوری صفر الی %45 و برای مدول ارتجاعی صفر الی %30 است. با توجه به  آزمایش‌های انجام شده، میزان مقاومت تک‌محوری و مدول تغییر شکل پذیری با افزایش حجم حفرات کروی بصورت نمایی کاهش می‌یابد. همچنین با افزایش اندازه حفرات از 4 به 6 میلی‌متر در نمونه‌های با درصد تخلخل یکسان، میزان کاهش مقاومت تک‌محوری و مدول ارتجاعی کمتر از 7 درصد است. در بخش دوم،  با توجه به اینکه مصالح متخلخل می‌تواند حالت خاصی از مواد مرکب در نظر گرفته شود، توسط روش میکرومکانیک و مدل‌‌های مختلف همگن‌سازی به بررسی اثر میزان حفرات کروی بر مدول ارتجاعی پرداخته شده است. با توجه به برازش انجام شده در محدوده تخلخل صفر الی %30، کاهش مدول ارتجاعی نسبت به حجم حفرات کروی را می‌توان با دقت بسیار مناسبی توسط روابط نمایی تعیین کرد. همچنین نتایج آزمایشگاهی تطابق مناسبی با مدل‌های همگن‌سازی که اثر شکل را لحاظ می‌کنند، دارد. در تخلخل‌های کمتر از %15 با توجه به اختلاف کم مدل‌های اشلبی، خودسازگار، موری-تاناکا و لایلنس، نتایج آزمایشگاهی تطابق مناسبی با آن‌ها دارد. با افزایش تخلخل نتایج آزمایش‌ها بیشتر به مدل‌های خودسازگار و اشلبی تمایل دارد.      }, keywords_fa = {حفرات بزرگ,مقاومت تک محوری,مدول ارتجاعی,مدل­سازی آزمایشگاهی,روش میکرومکانیک}, url = {https://ijme.iranjournals.ir/article_2932.html}, eprint = {https://ijme.iranjournals.ir/article_2932_2e08ada38b8095fd996f08d23e606735.pdf} } @article { author = {Goshtasbi, K and Zarei, V and Zoorabadi, M}, title = {Estimating The Deformation Modulus of Rock Mass With Use of Seismic Tomography}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {83-92}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Determination of rock mass deformation modulus is an important task in rock mechanics and rock engineering. There are direct and indirect procedures for estimating the deformation modulus. The determination of this parameter by direct (in situ) tests) requires considerable costs and involves difficult operational processes. For this reason, empirical equations for the indirect estimation of the modulus of deformation are an interesting issue for rock engineers and engineering geologists. Seismic travel time tomography uses seismic waves to for detection of structures the inside of the ground. This method has been widely applied to practical applications in many fields including rock engineering. Based on VP values obtained from seismic Tomography Tests and deformation modulus obtained from plate jacking tests that are performed in Rodbar Lorestan and Bakhteyari dams sites a relationship was suggested. This relationship are is compared with other exiting empirical relations. that lLowest error (of RMSE=4.133) and highest coefficient of correlations of (R=0.66) are obtained for suggested equation are obtained.  }, keywords = {Deformation modulus,in situ tests,tomography,seismic waves velocity (VP)}, title_fa = {تخمین مدول دگرشکل پذیری توده¬سنگ با استفاده از تموگرافی لرزه ای}, abstract_fa = {تعیین مدول دگرشکل‌پذیری توده سنگ اهمیت بسیار زیادی در مکانیک سنگ و مهندسی سنگ دارد. روش‌های مستقیم و غیر مستقیمی برای تخمین مدول دگرشکل پذیری وجود دارد. تعین این پارامتر با استفاده از روش‌های برجا (روش‌های مستقیم) نیازمند هزینه و مشکلات اجرایی است. به همین دلیل روش‌های غیر مستقیم تعیین مدول دگرشکل‌پذیری موضوع مورد علاقه مهندسان سنگ و زمین شناسان مهندسی است. به منظور ترسیم تصویری از زمین که تحت تأثیر امواج لرزه‌ای قرار گرفته است از توموگرافی اولین زمان رسید موج لرزه‌ای استفاده می‌شود. این روش به صورت گسترده‌ای در زمینه‌های زیادی از جمله مهندسی سنگ کاربرد پیدا کرده است. بر اساس مقایر سرعت موج برشی(Vp) که از آزمایش تموگرافی لرزه‌ای به‌دست آمده و همچنین مقادیر مدول دگرشکل پذیری به‌دست آمده از روش بارگذاری صفحه‌ای که در ساختگاه سد رودبار لرستان و بختیاری انجام شده اند، رابطه  بین مدول دگر شکل‌پذیری و سرعت موج لرزه ای پیشنهاد شده است. این رابطه با دیگر روابط تجربی موجود مقایسه شده است، که کمترین مقدار خطا(RMSE) و بیشترین مقدار ضریب همبستگی برای رابطه پیشنهادی به‌دست آمده است.}, keywords_fa = {مدول دگرشکل پذیری,روش های برجا,تموگرافی لرزه¬ای,سرعت موج لرزه ای(VP)}, url = {https://ijme.iranjournals.ir/article_3085.html}, eprint = {https://ijme.iranjournals.ir/article_3085_0cbff3a61873e728f94f56f90a38a270.pdf} } @article { author = {Shariat alavi, H and Ataei, M and Alizadeh Sevari, B and Serati, M and Zoorabadi, M}, title = {TBM Shield Selection Squeezing Ground, Case Study Part 2 Qomroud Tunel}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {93-106}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Qomroud tunnel with the total length of 35.7 kilometers is a part of large project which is under construction for transporting water from the Dez main stream to Qom city. Excavation analysis of the second lot of Qomroud tunnel, with the total length of 6+700 [i1] km, reveals that the occurrence of squeezing phenomenon is very probable in this specific part of tunnel. In order to select the best boring machine that suits the condition of tunneling in the second lot of Qomroud tunnel, this paper investigates the performance and efficiency of single and double shield tunnel boring machines (TBM) from the advance rate point of view and squeezing control parameters. To reach the objectives of the paper, NTH method is considered for estimating the advance rate parameter while tentative, semi tentative and theoretical- analytic methods are taken into account to evaluate the squeezing behavior of different geological features embedded in the tunnel’s length. Moreover, necessary over boring operation in different section of the tunnel is calculated using a numerical finite difference software (FLAC­2D) to overcome the convergence problem of the tunnel due to severe squeezing conditions. Results show that based on the dominant conditions, double-shield boring machine is more reliable and trustful in which it increases the tunneling efficiency and decreases the occurrence of jamming hazard.    [i1]?}, keywords = {Qomroud Tunnel,Mechanized Boring,Squeezing,NTH,Flac2D,Single Shield,Double Shield}, title_fa = {مقایسه فنی اقتصادی استفاده از ماشین¬های حفاری تمام مقطع سپری برای حفاری قطعه دوم تونل قمرود}, abstract_fa = {تونل قمرود به‌طول کلی 7/35 کیلومتر بخشی از طرح بزرگ انتقال آب از سرشاخه‌های حوضه دز به شهر قم است. برای حفاری قطعه 2 آن به طول 700+6 کیلومتر امکان استفاده از روش حفاری مکانیزه بررسی شده است. برآورد میزان مچاله شوندگی در مسیر قطعه دوم تونل قمرود نشان دهنده امکان رخ دادن پدیده مچاله شوندگی در متراژهای زیادی از مسیر تونل است. در این مقاله به منظور انتخاب نوع دستگاه حفر تونل تمام مقطع بررسی فنی و اقتصادی بر روی عملکرد 2 نوع سپر منفرد و سپر مضاعف (تلسکوپی) از لحاظ میزان پیشروی دستگاه حفر تونل تمام مقطع و مقابله با شرایط مچاله شوندگی صورت گرفته است. به‌منظور پیش‌ بینی نرخ پیشروی در واحدهای زمین شناسی مسیر تونل، از روش NTH که بر اساس 230 کیلومتر تونل‌سازی می‌باشد، استفاده شده است. میزان مچاله شوندگی با روش‌های تجربی، نیمه تجربی و تئوری- تحلیلی برآورد شده است و برای تخمین میزان همگرایی به‌منظور محاسبه میزان اضافه حفاری لازم برای غلبه بر پدیده مچاله شوندگی، نرم افزار Flac2D مورد استفاده قرار گرفته است. هدف از این مقاله بررسی فنی و اقتصادی بر روی نوع سپرهای دستگاه حفر تونل تمام مقطع در شرایط زمین‌های با قابلیت مچاله شوندگی است تا دستگاه مناسب انتخاب گردد ضمن این‌که امکان گیر افتادن دستگاه نیز در این مناطق به حداقل کاهش پیدا کند. با توجه به بررسی‌های فنی و اقتصادی صورت گرفته دستگاه حفر تونل تمام مقطع از نوع سپر مضاعف برای حفاری قطعه 2 پروژه قمرود گزینه برتر تشخیص داده شده است.}, keywords_fa = {تونل قمرود,حفاری مکانیزه,مچاله شوندگی,NTH,Flac2D,سپر منفرد و مضاعف}, url = {https://ijme.iranjournals.ir/article_3087.html}, eprint = {https://ijme.iranjournals.ir/article_3087_37d93168b5475525d2bfe90143776c8e.pdf} } @article { author = {Eshaqi, E and Kamkarrohani, A and Arabamiri, A.R}, title = {Two and Three Dimensional Modeling of Electrical Tomography Data Applied for Studying Qanat and Subsurface Shallow Structures}, journal = {Journal of Mining Engineering}, volume = {7}, number = {17}, pages = {107-112}, year = {2013}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {The electrical resistivity tomography is an optimal survey method of network of optimal network to [i1] detect subsurface targets using suitable arrays. Different optimization methods such as Guass-Newton and quasi-Newton methods are used to model and interpret acquired data. In this research, since there is a sufficient resistivity contrast between water qanat and its surrounding area exists in the qanat, it was selected as an appropriate target to considerfor investigation of advantages and disadvantages of electericalelectrical tomography method. The resistivity surveys were carried out into a regular network by 2-D and 3-D data acquisition methods. RES2DINV and RES3DINV computer softwares were used for 2-D and 3-D modeling respectively. Finally, in order to a better represent the resultsation, Voxler graphical software was used. Whereas Although the resulted qanat location is ambiguous in modeled 2-D and 3-D resistivity sections, it can clearly be determined by the resistivity decrease due to the wetness infiltration around the qanat. The relative sizes of the sediments and the clay content can qualitatively be estimated from the obtained resistivity sections.    [i1]از نویسنده سوال شود که آیا منظور این بوده است.}, keywords = {Electrical resistivity tomography,water qanat,2-D and 3-D modeling of resistivity data,Diole-dipole electrode configuration}, title_fa = {مدل¬سازی دوبعدی و سه بعدی داده¬های توموگرافی الکتریکی به منظور بررسی قنات¬ها و ساختارهای زیرسطحی کم عمق}, abstract_fa = {روش توموگرافی الکتریکی یک روش برداشت شبکه بهینه با استفاده از آرایه‌های مناسب در شناسایی اهداف زیرزمینی است. داده‌های اکتسابی در برداشت با استفاده از روش‌های مختلف بهینه‌سازی مانند روش‌های گوس- نیوتن، شبه نیوتن مورد مدل‌سازی و تفسیر قرار می‌گیرند. در این تحقیق قنات آب به دلیل دارا بودن تباین مقاومت ویژه کافی با محیط پیرامون، به عنوان هدف مناسب جهت بررسی مزایا و معایب روش توموگرافی الکتریکی انتخاب شد. برداشت‌ها به دو صورت دوبعدی و سپس سه‌بعدی در یک شبکه منظم برداشت شد. به ترتیب از نرم افزارهای RES2DINV و RES3DINV برای مدل‌سازی داده‌های دوبعدی و سه بعدی استفاده شد و در نهایت برای نمایش بهتر نتایج سه بعدی از نرم‌افزار Voxler استفاده شد. در  نتایج، موقعیت قنات در مقاطع دوبعدی و سه‌بعدی حاصل از مدل‌سازی، تا حدی مبهم بوده و به‌وضوح کامل دیده نمی‌شود اما می‌توان موقعیت آن را از روی کاهش مقاومت ویژه ناشی از نفوذ رطوبت به اطراف به صورت واضح مشخص کرد. وضعیت دانه‌بندی نسبی ذرات و وجود رس را نیز می‌توان به صورت کیفی در مقاطع به‌دست آمده تخمین زد.}, keywords_fa = {توموگرافی مقاومت ویژه الکتریکی,قنات,مدل¬سازی دوبعدی و سه¬بعدی داده¬های مقاومت ویژه,آرایه الکترودی دوقطبی- دوقطبی}, url = {https://ijme.iranjournals.ir/article_3088.html}, eprint = {https://ijme.iranjournals.ir/article_3088_824c90f0ebb873feb7b4f88bdcfbeaad.pdf} }