@article { author = {حسامی, رشاد and مالکی مقدم, مصطفی and بنیسی, صمد}, title = {A laboratory investigation of the effect of charge density on power draw in tumbling mills}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {1-8}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Power draw is one of the key parameters to control mill performance. It is dependent on various factors such as charge density, ore characteristics, ball sizes and type of the mill (AG, SAG, ball mill).  . In calculation of mills power draw, voidage and the fraction filled by the voidage in the charge is essential. In estimation of power draw, for the voidage between the balls a value of 40% is assumed for all the ball sizes. In this study it was found that the voidage between balls largely depends on the balls shapes and size distribution. The voidage between balls for 8, 9, 10, 11 and 12 mm ball sizes in both single size and seasoned balls was measured. By decreasing the ball size from 12 mm to 8 mm, the voidage decreased from 39.0% to 37.8%. The voidages with Bond chain with 11.4 and 7.6 mm top size balls were measured 36.0 and 35.2%, respectively. The effect of charge density on power draw was studied through scale-downing the ball size distribution of the Sarcheshmeh ball mills at the start up and the crush stop in a laboratory container. The voids of the two distributions were measured to be 33.5 and 36.1%, respectively. The difference in the amount of calculated power draw for these values of voidage was equal to 164 kW, which is equivalent to the weight of 15 tons of balls. An equation was proposed to correct the effect of bulk density on calculation of ball mill power draw.}, keywords = {power draw,Charge density,Voidage}, title_fa = {بررسی آزمایشگاهی تأثیر دانسیته بار بر توان کشی آسیاهای گردان}, abstract_fa = {توان‌کشی یکی از مهم‌ترین پارامترهای کنترلی آسیاهای گردان محسوب می‌شود. توان کشی به عوامل مختلفی از جمله دانسیته بار، خصوصیات ماده معدنی، اندازه گلوله و نوع آسیا وابسته است. اغلب در روابط ارائه شده جهت تخمین توان‌کشی، برای فضای خالی بین گلوله‌ها که تأثیر مستقیمی بر دانسیته بار دارد، عددی در حدود 40% در نظر گرفته می‌شود. در این تحقیق فضای خالی بین ذرات، از نسبت حجمی آب قرار گرفته بین ذرات به کل حجم تعیین شد. نتایج نشان داد که فضای خالی بین گلوله‌ها و ماده معدنی، به شکل و توزیع ابعادی آن‌ها بستگی دارد. مقدار فضای خالی برای گلوله و ماده معدنی در حالت تک‌اندازه به ترتیب، از 39% و 1/38%برای اندازه 12 میلی‌متری به 8/37% و 1/37% برای اندازه 8 میلی‌متری کاهش یافت. فضای خالی برای زنجیره گلوله پیشنهادی Bond با بزرگترین اندازه گلوله 4/11 و 8/8 میلی‌متر به ترتیب 36% و 2/35% به‌دست آمد. برای ماده معدنی با بزرگ‌ترین اندازه ذره 4/11 میلی‌متر و زنجیره ابعادی پیشنهادی Bond فضای خالی برابر با 5/34% اندازه‌گیری شد. نتایج نشان داد که فضای خالی بین گلوله ها در حالت زنجیره ابعادی کمتر از حالت تک‌اندازه است و با کوچک‌تر شدن اندازه بزرگ‌ترین گلوله زنجیره، فضای خالی کاهش می‌یابد. به‌منظور بررسی تغییرات دانسیته بار بر توان‌کشی در آسیاهای صنعتی،  زنجیره ابعادی گلوله آسیای گلوله‌ای مجتمع مس سرچشمه در ابتدای راه‌اندازی و در حین‌ کار که گلوله ها تحت سایش قرار گرفته‌اند با کوچک مقیاس کردن گلوله‌ها تحت آزمایش قرار گرفتند. مقدار فضای خالی در این دو حالت که نشانه تغییر توزیع دانه‌بندی گلوله‌ها در اثر سایش طی عملیات بود،  به ترتیب 5/33% و 1/36% به‌دست آمد. این میزان کاهش(6/2%) در فضای خالی به‌دلیل اضافه کردن گلوله جبرانی با بزرگ‌ترین اندازه تشخیص داده شد.  در این تحقیق، رابطه تخمین توان کشی Bond برای آسیاهای گلوله‌ای با در نظر گرفتن دانسیته بار تصحیح شد. }, keywords_fa = {توان کشی,فضای خالی,دانسیته بار}, url = {https://ijme.iranjournals.ir/article_22856.html}, eprint = {https://ijme.iranjournals.ir/article_22856_58c7b116dd5b5dff0e3b1d114f7d69c1.pdf} } @article { author = {Nazeri, Amin and Nejati, Hamid Reza and Ghazvinian, Abdolhadi}, title = {Effect of Nano SiO2 particles on the strength and fracture mechanism of cement based materials by AE technique}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {9-21}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Failure of many concrete and rock structures on the development of interior crack due to stress concentration at the crack tip shows the prominence of the fracture mechanism investigation of these structures. Using conventional methods for the design and analysis of steel, concrete and rock structures based on the criteria of stress and strength has raised many problems for the structure stabilities. Today, with increasing application of nanoparticles, studies focused on the effect of nanosilica on failure mechanism are rare. Addition of nanosilica to the concrete results in higher compressive, tensile and flexural strength; lower setting time and water permeability and higher resistance to chemical attacks. In this research, the internal mechanism of resistance and failure of concrete reinforced with silica nanoparticles was studied to achieve a better understanding of their mechanical behavior. For this purpose, various standard samples were studied including disc with a central crack (CSCBD) and cubes with similar mixtures (water, cement and aggregates), but different in the amount of silica nanoparticles (0, 0.5, 1, 1.5) in 7 and 28 days of curing time. Acoustic emission techniques (AE) was used for the monitoring of the failure process. It was revealed, parameters such as the number of count, stable and unstable crack growth, average frequency and RA index are also affected by varying the amount of silica nanoparticles in the concrete composition. The results showed that concrete with silica nanoparticles can withstand higher stress without unstable crack propagation. It is concluded that the addition of silica nanoparticles improves the fracture parameters of concrete.}, keywords = {Fracture toughness,Crack propagation,Nano SiO2 particles,Acoustic emission}, title_fa = {بررسی تاثیر نانو ذرات سیلیس بر مقاومت و مکانیزم شکست مواد پایه سیمانی با استفاده از سیستم انتشار آوایی}, abstract_fa = {شکست بسیاری از سازه‌های مهندسی بر اثر گسترش ترک با وجود پایین بودن نرخ بارگذاری روی آن‌ها در مقایسه با مقاومت تئوریکی سازه‌ها،لزوم درک دقیق مکانیزم و عوامل موثر بر گسترش ترک را آشکار می‌سازد. استفاده از روش‌های متداول تحلیل و طراحی سازه‌های فولادی، بتنی و سنگی بر مبنای معیار‌های تنش و مقاومت، تاکنون مشکلات زیادی در پایداری سازه‌ها به‌وجود آورده است. امروزه با توجه به گستردگی روز افزون نانو بتن‌ها، مطالعات تأثیر نانو ذرات بر مکانیزم شکست در این نوع بتن‌ها بسیار نادر است. در این تحقیق مکانیزم داخلی مقاومت و شکست بتن‌های مسلح شده با نانو ذرات سیلیسی مطالعه و بررسی  شده است. برای تحقق این موضوعاز نمونه‌های مختلف استوانه‌ای، دیسکی با ترک مرکزی (CSCBD) و مکعب مربع طبق استاندارد و ترکیب‌های یکسان (آب، سیمان و سنگ‌دانه) اما متفاوت در مقدار نانو ذرات سیلیس (0، 5/0، 1، 5/1) در بازه‌های مختلف نگهداری 7 و 28 روز استفاده شده است. برای رفتارنگاری فرآیند شکست نیز از تکنیک نوین انتشار آوایی (AE) استفاده شده است که با بررسی‌ پارامتر‌هایی نظیر تعداد کانت، گسترش ترک پایدار و ناپایدار، فرکانس متوسط و زاویه خیز نیز مشاهده می‌شود که با تغییرات مقدار درصد نانو ذرات سیلیس در خمیره بتن، این پارامتر‌ها نیز تغییر می‌کنند. می‌توان اینگونه بیان کرد که نتایج بیان‌گر رابطه خطی بین مقاومت و چقرمگی شکست مد برش و کشش نمونه‌ها بوده است، به‌طوری که بتن‌های با 1 درصد از نانو ذرات سیلیس بیشترین چقرمگی شکست را دارند و با افزایش و یا کاهش مقدار نانو ذرات سیلیس، مقاومت و چقرمگی شکست در هر دو مد شکست کاهش می‌یابد. همچنین نمونه‌های نانو بتن تحمل تنش‌های بالاتر بدون گسترش ترک ناپایدار را نسبت به بتن معمولی دارند و یا به عبارت بهتر نانو ذرات سیلیس باعث تاخیر در گسترش ترک ناپایدار در ساختار نمونه‌ها می‌شود.}, keywords_fa = {چقرمگی شکست,گسترش ترک,نانو ذرات سیلیس,انتشار آوایی}, url = {https://ijme.iranjournals.ir/article_22853.html}, eprint = {https://ijme.iranjournals.ir/article_22853_73b611210f7397824522f181717fcbeb.pdf} } @article { author = {Shahami, Mirhossein and Yarahmadi Bafghi, Ali Reza and گرایلی میکلا, روزبه}, title = {Evaluate the capability of key-groups method development using numerical methods for finding the critical key-group in stability analysis of rock slopes}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {23-32}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {The key block is a well-known method in stability analysis of jointed rock slope. This method is based on the finding & analysis of the key block. In this method if none one of the blocks were unstable we can conclude the rock mass is stable. Sometimes a collection of some stable blocks makes an unstable group, therefore the stability analysis of jointed rock masses leads to investigation of the groups of blocks that are potentially dangerous for the stability of a rock slope. The key-groups method detects the critical groups and focuses the stability calculations on them. For three dimensional development and also increase the efficiency, accuracy and speed of key-group method, combining it with numerical methods is focused. This objective can be achieved in two parts: A: finding the critical key-group and analysing the interaction between the blocks of a key-group. B: analysing the interaction between the critical key-group and rock mass and analyse the stability of rock mass. In this research the blocks interaction of key-groups was analysed, firstly to evaluate the performance of the key-groups method and then to choose the best numerical methods for method development based on fuzzy multi criteria decision maker. At the end, discontinuous deformation analysis was selected as the compatible numerical method with standards. These two methods were combined and the algorithm as well as the primary program were prepared in mathematica software. The results reveals combining the key-groups method with numerical methods results in good performance of identifying and assessing the sustainability of key-groups.}, keywords = {Stability analysis,key blocks,key-groups,discontinuous deformation analysis,Fuzzy Multi criteria Decision Making}, title_fa = {بررسی قابلیت توسعه روش گروه های کلیدی با روش های عددی برای یافتن گروه کلیدی بحرانی در تحلیل پایداری شیب های سنگی}, abstract_fa = {ناهمسانی و وجود ناپیوستگی‌ها، در مقاومت و رفتار توده سنگ نقش اساسی دارد. امروزه مهندسین با محدوده وسیعی از روش‌ها، به‌منظور تحلیل پایداری شیب های سنگی مواجه هستند. به‌دلیل سادگی و سرعت اجرا، روش‌های به‌کار رفته در تحلیل‌های استاتیکی همچنان جایگاه ویژه‌ای در بررسی پایداری شیب های سنگی درزه‌دار دارند. یکی از معروف‌ترین روش‌های استاتیکی موجود در تحلیل پایداری توده سنگ‌های درزه‌دار، تئوری بلوکی و روش بلوک‌ها ی کلیدی است که تنها برمبنای یافتن و تحلیل بلوک کلیدی بوده و چنان‌چه هیچ یک از این بلوک‌ها  ناپایدار نباشند، دلالت بر پایداری توده سنگ می‌کند. در بعضی مواقع، اجتماع تعدادی بلوک پایدار منجر به تشکلیل گروهی شده که اغلب سبب ناپایداری می‌شود؛ بنابراین تحلیل پایداری توده سنگ درزه‌دار، منجر به بررسی گروه‌هایی از بلوک‌ها  می‌شود که به‌صورت بالقوه برای پایداری یک شیب سنگی خطرناک می‌باشند. روش گروه‌های کلیدی با عملکردی پیشرونده اقدام به معرفی این گروه‌های بحرانی کرده و محاسبات پایداری را در آن‌ها متمرکز می‌کند. برای افزایش کارایی، دقت و سرعت روش گروه‌های کلیدی و همچنین توسعه آن در سه بعد، تلفیق آن با یکی از روش‌های عددی مورد توجه است، تا ضمن توسعه این روش مشکل زمان زیاد محاسبه در کدهای رایآن‌های مربوط به روش‌های عددی مرتفع شود. این هدف در دو بخش تحقق می‌یابد: الف) تحلیل اندرکنش بلوک‌ها ی یک گروه کلیدی و یافتن گروه کلیدی بحرانی ب) تحلیل اندرکنش گروه کلیدی بحرانی با توده سنگ و بررسی پایداری توده سنگ. در این مقاله با هدف تحلیل اندرکنش بلوک‌های گروه کلیدی، ابتدا به بررسی عملکرد روش گروه‌های کلیدی پرداخته و سپس برای انتخاب بهترین روش عددی برای توسعه، از روش تصمیم‌گیری چندشاخصه فازی بهره گرفته شده است. در پایان روش تحلیل تغییر شکل ناپیوسته (DDA) به‌عنوان سازگارترین روش عددی با معیارهای توسعه، انتخاب شد و سپس تلفیق این دو روش، مورد توجه قرار گرفت و الگوریتم و برنامه اولیه در محیط نرم افزاری Mathematica تهیه شد. نتایج این مرحله از توسعه روش گروه‌های کلیدی که عملا نوعی تلفیق با روش تحلیل تغییر شکل ناپیوسته است، بیان‌گر قابلیت توسعه روش گروه های کلیدی در شناسایی و تحلیل پایداری گروه‌های کلیدی بحرانی در شیب های سنگی درزه دار است.  }, keywords_fa = {تحلیل پایداری,بلوک کلیدی,گروه‌های کلیدی,تحلیل تغییر شکل ناپیوسته,تصمیم‌گیری چندمعیاره فازی}, url = {https://ijme.iranjournals.ir/article_22857.html}, eprint = {https://ijme.iranjournals.ir/article_22857_312b7487ca3229e9dcf2a0eb8aff33aa.pdf} } @article { author = {سرفرازی, وهاب and میخک بیرالوند, نسرین}, title = {Effect of the Tensile Strength to Confining Pressure Ratio on Penetration of U Shape Disc using Discrete Element Method}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {33-45}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {In this paper, the effect of the ratio of tensile strength to confining pressure on the penetration of U Shape disc has been investigated using Discrete Element Method. For this purpose, three numerical models with different tensile strength of 5 MPa, 15 MPa and 25 MPa were built. From each model two similar samples were prepared and compressed by two different confining pressures of 5 MPa and 25 MPa, respectively. The U shape cutter penetrates in the model by the rate of 0.02 m/s till 4 mm of disc is penetrated. In total, 6 simulations have been done. The rock materials, below the cutters, show three different mechanical behavior including failure, plastic and elastic behavior. The failure zone is fully fractured while the plastic zone is consisted of partially micro crack with several major fractures. The elastic zone has remained undamaged. The effect of the ratio of tensile strength to confining pressure has substantial effect on the extension of three introduced zones. When tensile strength is 5 MPa, the initiation force and failure stress is increased by increasing the tensile strength but the extension of failure zone and chipping thickness is decreased. When tensile strength is 25 MPa, the initiation force, failure stress, extension of failure zone and thickness of chipping is constant by increasing the tensile strength.}, keywords = {disc,Tensile strength,confining pressure,particle flow code}, title_fa = {مطالعه تأثیر نسبت مقاومت کششی به فشار محصورکننده بر نفوذ دیسک U شکل TBM توسط روش اجزائ گسسته}, abstract_fa = {در این تحقیق با استفاده از روش اجزای مجزا تأثیر نسبت مقاومت کششی به فشار محصورکننده بر نفوذ دیسک U شکل TBM بررسی شده است. بدین منظور، سه مدل عددی با مقاومت‌های کششی متفاوت MPa 5، MPa 15 و MPa 25 ساخته شد. از هر مدل دو نمونه مشابه آماده شد و تحت دو تنش محصورکننده MPa5 و MPa 25 قرار گرفت. به‌طور کلی 6 مدل‌سازی انجام شد. بعد از اعمال فشار جانبی، برنده با نرخ m/s 02/0 به میزان mm4 در سنگ نفوذ کرده و باعث شکست سنگ می‌شود. سنگ زیر برنده سه رفتارمکانیکی مختلف را نشان می‌دهد که عبارتند از: ناحیه شکسته شده زیر برنده، ناحیه پلاستیک با ترک‌های موضعی زیر ناحیه شکسته شده و ناحیه الاستیک. نتایج نشان می‌دهند که نسبت مقاومت کششی به فشار محصورکننده تأثیر بسزایی بر وسعت نواحی شکسته شده دارد. در فشار محصور کننده MPa 5، با افزایش مقاومت کششی نیروی شروع ترک، تنش شکست افزایش می‌یابد ولی وسعت شکست و میزان نفوذ دیسک کم می‌شود. همچنین در فشار محصور کننده  MPa 25، با افزایش مقاومت کششی نیروی شروع ترک، تنش شکست، وسعت شکست و میزان نفوذ دیسک تقریبا ثابت است.}, keywords_fa = {نرم‌افزار PFC2D,برنده,مقاومت کششی,فشار محصورشوندگی,کد جریان ذره}, url = {https://ijme.iranjournals.ir/article_22858.html}, eprint = {https://ijme.iranjournals.ir/article_22858_574477f4eb85c15d7709c27256776da3.pdf} } @article { author = {Moosavirad, Seyed Morteza and Abaspour Sirjani, Maryam}, title = {Assessment of Electrocoagulation Method to Reduce Total Suspended Solids, Turbidity and Hardness of Thickener Overflow of hematite in Gole-Gohar Sirjan}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {47-57}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Electrocoagulation process is one of the new and progressing methods to remove suspended matter. In this study, electrocoagulation was assessed to reduce total suspended solids (TSS), turbidity and hardness of the thickener overflow of hematite in Gole-Gohar Sirjan. Therefore, in a laboratory scale, a glass container with 3 liter volume was prepared and equipped with 6 electrodes made of iron, steel and aluminum. Parameters such as electrode material, contact time and voltage were studied. The aluminum electrode showed the highest TSS removal comparing to the iron and steel electrodes. Aluminum electrode in a voltage of 6V and retention time of 5 minutes removed 88.5 percent of TSS  while the steel electrode in voltage of 6 V and retention time of 15 minutes have maximum turbidity equal to 81% (NTU 21). Also in various voltages and different retention times, there was no significant change in the hardness. Based on the technical and economic studies, capital, operating and maintenance costs for electrodes of aluminum, iron and steel were calculated separately. The results illustrated that iron electrode with respect to the total costs (878 Ria) is preferred in comparison with steel (2978 Ria) and aluminum electrodes (3160 Ria). The iron electrode is selected based on the ease of operation, the settling of solid sludge, dewatering capability suitable and less sludge production volume.}, keywords = {Total Suspended Solids,electrocoagulation,Total Hardness,Technical and Economic studies,Overflow Thickener}, title_fa = {بررسی روش الکتروکواگولاسیون برای کاهش ذرات معلق، در سرریز تیکنر}, abstract_fa = { فرایند الکتروکواگولاسیون از جمله فرآیندهای جدید و رو به رشدی است که به نحوه چشم‌گیری به‌منظور حذف ذرات معلق آب استفاده قرار شده است. در این تحقیق به بررسی روش الکتروکواگولاسیون برای کاهش کل ذرات جامد معلق (TSS) ، کدورت و سختی در آب سرریز تیکنر هماتیت گل‌گهر سیرجان پرداخته شده است. بدین منظور در مقیاس آزمایشگاهی محفظه شیشه‌ای به حجم 3 لیتر و مجهز به 6 الکترود ساخته شد. الکترودها از جنس آهن ، استیل و آلومینیوم، که به‌صورت مجزا در هر یک از انواع الکترود قرار گرفته‌اند. پارامترهای جنس الکترود، مدت زمان تماس و ولتاژ بررسی شد. نتایج نشان داد که الکترود آلومینیوم نسبت به الکترودهای آهن و استیل بیشترین میزان حذف TSS را دارد. به‌طوری‌که در ولتاژ 6 ولت و زمان ماند 5 دقیقه، TSS به میزان 5/88 درصد حذف شده است. از طرفی الکترود استیل در ولتاژ 6 ولت و مدت زمان ماند 15 دقیقه بالاترین مقدار حذف کدورت  برابر با 81% (NTU 21 ) را دارد. همچنین در ولتاژهای مختلف و زمان ماندهای متفاوت هیچ‌گونه تغییر قابل‌توجهی در سختی مشاهده نشد. بر اساس بررسی فنی و اقتصادی،هزینه‌های سرمایه‌ای، عملیاتی و نگهداری برای الکترودهای آلومینیوم، آهن و استیل به‌طور جداگانه محاسبه شد. نتایج نشان داد الکترود آهن با توجه به کل هزینه‌های اجرایی( 878 ریال ) نسبت به الکترودهای استیل( 2978 ریال) و الکترود آلومینیوم( 3160ریال ) ارجحیت دارد. از طرفی الکترود آهن با توجه به سهولت در بهره‌برداری، قابلیت ته نشینی خوب لجن تولیدی، قابلیت آبگیری مناسب و تولید حجم لجن کمتر، مناسب تشخیص داده شده است.}, keywords_fa = {کل ذرات جامد معلق,الکتروکواگولاسیون,سختی کل,بررسی فنی و اقتصادی,سر ریز تیکنر,گل‌گهر سیرجان}, url = {https://ijme.iranjournals.ir/article_22855.html}, eprint = {https://ijme.iranjournals.ir/article_22855_52c80301794fb8e6a0e9fd18c9744ac9.pdf} } @article { author = {یونس مومنی, یعقوب and حسینی, محمد فاروق}, title = {Stability analysis of Bakhtiary concrete arch dam abutments using upper bound theorem}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {59-71}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Today, large dams are constructed with the different purposes of hydroelectric energy production, tourist attraction, increasing downstream life dams, etc. Concrete arch dams are one of the most affordable large-scale dam construction methods. Much of the reservoir pressure are supported by the abutments in concrete arch dams. This, in turn, highlights the significance of the stability of concrete arch dam abutment. Traditional method of abutment stability analysis calculates the safety factor of potentially slipping wedges using limit equilibrium. In this method rock wedges are considered rigid with no internal discontinuity. In this research, after a short review of geological structure of Bakhtiary dam site and recognition of potential slip wedge, the load distribution of abutments are estimated using finite element method. In numerical modeling, a least simplification in dam body and abutment geometry is purposed. Infinite elements are used to reduce effect of boundary condition. Finally, stability of Bakhtiary arch dam abutments slip wedges has been approved by the application of upper bound theorem. Despite the limit equilibrium method, the proposed method is based on energy-work balances and is able to account for the effect of internal discontinuities yield.}, keywords = {Concrete arch dam,Abutment,Upper bound theorem}, title_fa = {تحلیل پایداری تکیه گاه های ساختگاه سد بتنی قوسی بختیاری با استفاده از تئوری حدبالا}, abstract_fa = {    امروزه سدهای بزرگ با اهدافی نظیر تولید انرژی برق‌آبی، ایجاد مناطق گردشگری، افزایش عمر سد‌های پایین‌دست و مواردی از این دست احداث می‌شوند. سدهای بتنی قوسی از جمله مقرون به صرفه‌ترین روش‌های سدسازی در مقیاس بزرگ هستند. بخش عمده‌ای از تحمل بار ناشی از فشار مخزن در سد‌های قوسی به عهده تکیه‌گاه‌های آن است. این موضوع تأکیدی بر اهمیت بالای تحلیل پایداری تکیه‌گا‌ه‌ها در این نوع سد‌ها است. روش سنتی معمول برای تحلیل پایداری تکیه‌گاه‌های یک سد استفاده از روش تعادل حدی برای محاسبه ضریب ایمنی گوه‌های مستعد لغزش است. در روش مذکور، گوه‌های سنگی صلب و فاقد ناپیوستگی داخلی درنظرگرفته می‌شوند. در تحقیق پیش‌رو، پس از مروری کوتاه بر وضعیت زمین‌شناسی ساختگاه طرح سد و نیروگاه بختیاری و شناخت گوه‌های مستعد لغزش در محل تکیه‌گاه‌های سد، نیروی وارد بر تکیه‌گاه‌ها با استفاده از روش اجزای محدود تخمین زده شده ‌‌است. در فرآیند مدل‌سازی عددی سعی بر این است که هندسه بدنه سد و تکیه‌گاه‌ها با حداقل ساده‌سازی، شبیه‌سازی شوند. همچنین برای اطمینان از عدم تأثیر فواصل مرزی بر نتایج مدل‌سازی، از المان‌های نیمه‌ بی‌نهایت در مرزها بهره گرفته ‌شده‌ است. درنهایت پس از تخمین توزیع بارهای بدنه سد بر تکیه‌گاه‌ها، پایداری گوه‌های مستعد لغزش با استفاده از تئوری حدبالا تأیید شده ‌است. روش مذکور، روشی مبتنی بر تعادل کار و انرژی است که بر خلاف روش تعادل حدی توانایی بررسی تسلیم در ناپیوستگی‌های داخلی گوه ‌سنگی را دارد. }, keywords_fa = {سد بتنی قوسی,تکیه گاه,تئوری حدبالا}, url = {https://ijme.iranjournals.ir/article_22859.html}, eprint = {https://ijme.iranjournals.ir/article_22859_6d4588ae4f396717cd414c0b92e65837.pdf} } @article { author = {Hossein Morshedy, Amin}, title = {Deposit Zoning based on the spatial distribution of ore grade using self-organizing map clustering algorithm- Case study: Choghart iron deposit}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {73-86}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {Deposit zoning is one of the significant issues in the field of modelling, evaluation and exploitation planning in the mining sector. In ore modelling, the site is divided into zones based on the physical features affecting mineralization or the spatial distribution of ore grade. In this research, self-organizing map (SOM) has been used for three-dimensional zoning of the mineral deposits. The cluster validity indices has been applied to define the optimal number of zones. The proposed algorithm verified using the data of Choghart iron deposit. The Clustering validation indices were executed based on assay data (iron and phosphorus) of exploratory boreholes and optimal number was resulted in two zones. The SOM clustering algorithm was utilized to determine the confine of each zone and assigning samples within the two zones. As a result, the output of SOM and K-means algorithms illustrated that about 90% of the data was similarly assigned to the same cluster. In SOM clustering, the discrimination surface of the two zones has the northeast-southwest orientation with the southeast slope, while the K-means algorithm determined the surface with east-west orientation and south slope. The resulting surface of SOM is in accordance with the dimensional and directional properties of the structural features (especially fault system) in Choghart iron deposit.}, keywords = {Zoning,Clustering,Cluster validity index,Self-organizing map,Choghart iron deposit}, title_fa = {پهنه بندی کانسار براساس توزیع فضایی عیار کانسنگ با استفاده از الگوریتم خوشه بندی نقشه خود سازمانده در معدن چغارت}, abstract_fa = {پهنه‌ بندی کانسار، یکی از مسائل مهم در زمینه مدل‌سازی، ارزیابی و برنامه‌ریزی استخراج در امور معدنی است. در مدل‌سازی‌های معدنی، منطقه بر اساس ویژگی‌های فیزیکی مؤثر بر کانی‌زایی یا توزیع فضایی عیار به ‌پهنه‌های مختلف تقسیم می‌شود. در این مقاله، از روش خوشه بندی نقشه خودسازمانده (SOM) به‌منظور پهنه‌بندی سه بعدی کانسار معدنی استفاده شده است و شاخص‌های اعتبارسنجی برای تعیین تعداد بهینه پهنه‌ها به‌کار برده شده است. به‌منظور اعتبارسنجی الگوریتم پیشنهادی، داده‌ها و اطلاعات معدن سنگ آهن چغارت به‌کار برده شده است. شاخص‌های اعتبارسنجی خوشه بندی روی داده‌های عیارسنجی آهن و فسفر گمانه‌های اکتشافی اجرا شد و در نتیجه تعداد دو پهنه به‌صورت بهینه مشخص شد. بر اساس نتایج، محدوده دو پهنه و نحوه اختصاص نمونه به هر پهنه با استفاده از الگوریتم خوشه‌بندی نقشه خودسازمانده تعیین شد. در نتیجه، خروجی الگوریتم‌های SOM و K-means بررسی شد که در حدود 90% داده‌ها به‌صورت مشابه به‌خوشه‌های یکسان اختصاص یافته است. در روش SOM، سطح جدایش دو پهنه در راستای شمال‌شرقی-جنوب‌غربی کشیده شده که به سمت جنوب‌شرقی شیب دارد، در حالی که این سطح جدایش در روش K-means راستای شرقی-غربی و شیب به‌سمت جنوب دارد. بر اساس سطوح جدایش به‌دست آمده از دو روش خوشه‌بندی و مقایسه با خصوصیات بعدی-جهتی و ویژگی‌های ساختمانی مؤثر در کنترل کانی‌زایی (به‌ویژه گسل‌ها)، سطح جدایش SOM از نظر ساختار فضایی و جهتی، هم خوانی قابل‌توجهی با ویژگی‌های ساختمانی منطقه دارد.}, keywords_fa = {پهنه بندی,خوشه بندی,شاخص اعتبارسنجی خوشه بندی,نقشه خودسازمانده,سنگ آهن چغارت}, url = {https://ijme.iranjournals.ir/article_22854.html}, eprint = {https://ijme.iranjournals.ir/article_22854_1b42f64eda47a6347cd14daeed475600.pdf} } @article { author = {Sabeti, Hamid and Moradzadeh, Ali and Doulati Ardejani, Faramarz and Soares, Amilcar}, title = {3D Geostatistical simulation of acoustic impedance using improved direct sequential simulation algorithm}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {87-107}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {}, keywords = {Geostatistical simulation,acoustic impedance,improved direct sequential simulation,variogram}, title_fa = {شبیه‌سازی زمین‌آماری سه‌بعدی داده‌های مقاومت صوتی با استفاده از الگوریتم شبیه‌سازی متوالی مستقیم بهبودیافته}, abstract_fa = {شبیه‌سازی زمین‌آماری امکان تولید مدل‌های دو و سه‌بعدی با استفاده از داده‌های اندازه‌گیری شده در محل‌های محدود (چاه) را فراهم می‌‌کند. در این مطالعه، روش جدیدی به نام شبیه‌سازی متوالی مستقیم بهبودیافته ارائه شده و با روش شبیه‌سازی متوالی مستقیم رایج، برای شبیه‌سازی داده‌های مقاومت صوتی مقایسه شده است. در الگوریتم رایج پارامترهای شبیه‌سازی واریوگرام و تابع توزیع احتمالاتی به‌صورت کلی معرفی می‌شود بنابراین احتمال توزیع فضایی نامناسب مقادیر شبیه‌سازی شده در نتیجه الگوریتم وجود دارد. در روش بهبودیافته، امکان معرفی این پارامترها به‌صورت محلی به الگوریتم شبیه‌سازی فراهم شده است. تحلیل و بررسی مقاطع قائم از مقادیر شبیه‌سازی شده توسط روش رایج و بهبودیافته روی داده مصنوعی نشان می‌دهد که در روش بهبودیافته مقادیر شبیه‌سازی شده توزیع فضایی مناسب‌تری دارند. همچنین هر دو روش رایج و بهبودیافته بر روی یک داده واقعی اعمال شده است. مقایسه نتایج نشان‌دهنده بهبود عملکرد روش جدید نسبت به روش رایج است. ضمن اینکه هیستوگرام محلی در نتیجه الگوریتم بهبودیافته بازتولید شده است. همچنین برای تحلیل عدم قطعیت، 100 خروجی شبیه‌سازی با استفاده از هر دو روش تولید شده است تا امکان محاسبه واریانس در هر سلول به‌وجود آید. کاهش واریانس و در نتیجه کاهش عدم قطعیت در روش بهبودیافته، هم در مورد داده مصنوعی و هم در مورد داده واقعی، مؤید کارایی بهتر این روش نسبت به روش رایج است.}, keywords_fa = {شبیه‌سازی زمین‌آماری,مقاومت صوتی,شبیه‌سازی متوالی مستقیم بهبود یافته,واریوگرام}, url = {https://ijme.iranjournals.ir/article_22860.html}, eprint = {https://ijme.iranjournals.ir/article_22860_97cccb6d04519e2f318d964e0a77d71f.pdf} } @article { author = {radmehr, vahid and شفائی تنکابنی, سیدضیاءالدین and نوع پرست, محمد and عبداللهی, هادی}, title = {Evaluation of flotation circuit arrangement with integrated linear circuit analysis and signal flow graph- Case study: Qaleh-Zari copper factory}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {119-128}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {In flotation circuits, staged separation is used to produce a product with desired recovery and quality. Since usually million tons of mineral ore are upgraded in flotation circuits annually, achieving small improvement through the circuit re-arrangement can have substantial economic effect. In the other hand, there are various designs for a flotation circuit and finding the best combination experimentally is time consuming and costly. In this research, the principles of linear circuit analysis is used to develop a mathematical correlation between the rows of flotation circuit cells. This is performed by considering the transfer function for each cell row and then apply the appropriate criteria for evaluating the circuit transfer function. Since, signal flow graphs can be more easily and efficiently used for analytical method, it is replaced in block diagram for transfer function. This facilitates examination of the large and complex arrangements of flotation circuits. The arrangement of the Qaleh-Zari copper flotation circuit was evaluated by this method. The results showed that by modifying the flotation circuit arrangement, separation sharpness increased from 1.62 to 1.83. This increase can improve the separation of intermediate material in the flotation circuit. It was also shown that if the recovery is determined for each bank, the flow rate of output can be assessed and calculated precisely, and consequently the probable errors can be prevented. The results of this method can be used in circuit design or modification of plant circuit layout.}, keywords = {"flotation circuit arrangement","linear circuit analysis","Qaleh-Zari copper plant","signal flow graph"}, title_fa = {ارزیابی چیدمان مدارهای فلوتاسیون با تلفیق روش تحلیل مدار‌خطی و نمودار جریان سیگنال، درکارخانه مس قلعه زری}, abstract_fa = {در مدارهای فرآوری مواد معدنی، از جدایش مرحله‌ای برای تولید محصولی با بازیابی و کیفیت مناسب استفاده می‌شود. چون به‌طور معمول، سالانه میلیون‌ها تن ماده معدنی در این مدارها تحت عملیات پرعیارسازی قرار می‌گیرد، دستیابی به بهبودی اندک از طریق تغییر در چیدمان مدار می‌تواند تاثیر اقتصادی قابل‌توجهی داشته باشد. همچنین چون برای یک مدار جدایش، طرح‌های مختلفی وجود دارد یافتن بهترین ترکیب از طریق انجام آزمایش، زمان‌بر و پرهزینه است. در این تحقیق، از اصول تحلیل مدار برای ایجاد ارتباط ریاضی بین مراحل مختلف در مدارهای فرآوری استفاده شده است. این کار با در نظر گرفتن بازیابی به‌عنوان تابع انتقال برای هر مرحله و سپس استفاده از معیار دقت جدایش برای ارزیابی تابع انتقال مدار انجام شد. چون محاسبات دستی فراوان سبب محدود شدن روش تحلیل مدار شده است؛ برای تسریع در انجام محاسبات، علاوه بر پیاده‌سازی روش تحلیل مدار در نرم‌افزار متلب، گراف‌های جریان سیگنال و فرمول بهره میسون به‌عنوان جایگزینی برای دیاگرام‌ها بلوکی معرفی شد. در نتیجه، این امکان ایجاد شد تا چیدمان‌ مدارهای با تعداد مراحل زیاد و پیچیده بررسی شود. روش پیشنهادی بر روی یک مدار با 6 مرحله پرعیارسازی پیاده شد. با اصلاح چیدمان مدار، دقت جدایش از 49/1 به 2/2 افزایش یافت. این افزایش می‌تواند به بهبود جدایش مواد میانی در مدار جدایش کمک کند. همچنین نشان داده شد که اگر بازیابی مربوط به هر بانک مشخص باشد با توجه به دبی فلز ورودی به شبکه جدایش می‌توان دبی فلز در هر یک از جریان‌ها را محاسبه کرد.}, keywords_fa = {چیدمان مدار,گراف جریان سیگنال,تحلیل مدار,نرم افزار متلب}, url = {https://ijme.iranjournals.ir/article_23216.html}, eprint = {https://ijme.iranjournals.ir/article_23216_cd557dc7895bcd004b2a1c05fa98460a.pdf} } @article { author = {بارانی بیرانوند, کیانوش and قربانی مقدم, میثم}, title = {Effect of Ore Characteristics on the AG Mill Circuit Performance of Gole-Gohar Iron Ore Processing Plant}, journal = {Journal of Mining Engineering}, volume = {11}, number = {32}, pages = {109-117}, year = {2016}, publisher = {Iranian Society of Mining Engineering (IRSME)}, issn = {1735-7616}, eissn = {2676-4482}, doi = {}, abstract = {In this research the effect of feed characteristics on AG mill performance of Gole-Gohar iron ore processing plant was studied. For this purpose, 11 surveys in industrial scale were conducted on the circuit. At each survey for 2 hours, samples from AG mill feed and product were collected and mill data such as feed rate and power draw were recorded. Also for the evaluation of the effect of feed size distribution, in 3 surveys, feeder conveyor was stopped and all material on 25 meters of the belt were collected. SAG mill power index (SPI), was determined as the index of feed materials hardness. The result showed with increasing SPI, the product particle size decreased. A harder feed material produces more critical particles in the mill which elevates the mill volume content. It is expected that with increasing ore hardness, abrasion and attrition breakage mechanisms dominate and the product will be finer. Also the results showed, the SPI indexes increased with increasing the ratio of coarse particles (+100mm) to medium particles (-100+40mm).}, keywords = {AG mill, Ore hardness,Feed characterization,Gole-Gohar}, title_fa = {بررسی تأثیر مشخصات بار ورودی بر عملکرد آسیای خودشکن خط‌سه‌کارخانه منیتیت شرکت گل گهر سیرجان}, abstract_fa = {در این تحقیق تأثیر مشخصات بار ورودی بر عملکرد آسیای خودشکن خط 3 کارخانه فرآوری سنگ آهن گل‌گهر بررسی شده است. برای این منظور 11  پیمایش در مقیاس صنعتی از مدار آسیای خود‌شکن انجام و در هر پیمایش به مدت 2 ساعت از خوراک و محصول آسیا، نمونه‌گیری و همچنین  اطلاعات آسیا شامل نرخ خوراک و توان مصرفی آسیا ثبت شده است. همچنین به‌‌منظور بررسی تأثیر دانه‌بندی در سه پیمایش نوار نقاله خوراک متوقف و کل مواد روی نوار به طول تقریبی 25 متر به‌عنوان نمونه برداشته شده است. در این تحقیق از شاخص SPI به‌عنوان شاخص سختی آسیای کنی خودشکن و نیمه‌خودشکن استفاده شده است. نتایج نشان داده که با افزایش شاخص SPI خوراک محصول آسیا دانه ریزتر شده است. افزایش سختی بار ورودی موجب ایجاد ذرات با ابعاد بحرانی در آسیا شده و در نتیجه حجم بار داخل آسیا افزایش یافته است. افزایش حجم بار داخل آسیا منجر به غالب شدن مکانیزم‌های سایش و فرسایش شده و در نتیجه محصول خردایش دانه‌ریز  شده است. بررسی تأثیر توزیع دانه‌بندی خوراک نشان داده که  نسبت ذرات با ابعاد درشت (100+ میلی‌متر) به ذرات با ابعاد متوسط (40+100- میلی‌متر) رابطه معکوسی با شاخص SPI دارد. مشاهده شده است که با کاهش نسبت ذرات درشت به متوسط، شاخص SPI افزایش یافته و محصول تولیدی ریزتر شده است.}, keywords_fa = {آسیای خودشکن,SPI,سختی کانسنگ,مشخصات خوراک,گل گهر}, url = {https://ijme.iranjournals.ir/article_23217.html}, eprint = {https://ijme.iranjournals.ir/article_23217_8393a2c1838d3995a5a9b21ea46fe3c3.pdf} }